- 您现在的位置：买卖IC网 > PDF目录268181 > NAND01GW3B2AN6F (NUMONYX) 128M X 8 FLASH 3V PROM, 25000 ns, PDSO48 PDF资料下载
参数资料
| 型号： | NAND01GW3B2AN6F |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 128M X 8 FLASH 3V PROM, 25000 ns, PDSO48 |
| 封装： | 12 X 20 MM, LEAD FREE, PLASTIC, TSOP-48 |
| 文件页数： | 20/64页 |
| 文件大小： | 632K |
| 代理商： | NAND01GW3B2AN6F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
NAND01G-B, NAND02G-B
Device operations
27/64
6.3
Page Program
The Page Program operation is the standard operation to program data to the memory
array. Generally, data is programmed sequentially, however the device does support
Random Input within a page.
The memory array is programmed by page, however partial page programming is allowed
where any number of Bytes (1 to 2112) or Words (1 to 1056) can be programmed.
The maximum number of consecutive partial page program operations allowed in the same
page is eight. After exceeding this a Block Erase command must be issued before any
further program operations can take place in that page.
6.3.1
Sequential Input
To input data sequentially the addresses must be sequential and remain in one block.
For Sequential Input each Page Program operation consists of five steps (see Figure 10):
1.
one bus cycle is required to setup the Page Program (Sequential Input) command (see
2.
four or five bus cycles are then required to input the program address (refer to Table 6
and Table 7)
3.
the data is then loaded into the Data Registers
4.
one bus cycle is required to issue the Page Program confirm command to start the
P/E/R Controller. The P/E/R will only start if the data has been loaded in step 3.
5.
the P/E/R Controller then programs the data into the array.
6.3.2
Random Data Input
During a Sequential Input operation, the next sequential address to be programmed can be
replaced by a random address, by issuing a Random Data Input command. The following
two steps are required to issue the command:
1.
one bus cycle is required to setup the Random Data Input command (see Table 10)
2.
two bus cycles are then required to input the new column address (refer to Table 6)
Random Data Input can be repeated as often as required in any given page.
Once the program operation has started the Status Register can be read using the Read
Status Register command. During program operations the Status Register will only flag
errors for bits set to '1' that have not been successfully programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be
accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to
the Command Interface.
相关PDF资料 |
PDF描述 |
|---|---|
| NAND08GW3B2CZC1 | 1G X 8 FLASH 3V PROM, 35 ns, PBGA63 |
| NAND01GR3B3CZA1 | 128M X 8 FLASH 1.8V PROM, 35 ns, PBGA63 |
| NAND02GR4B2BZB1 | 128M X 16 FLASH 1.8V PROM, 35 ns, PBGA63 |
| NCH030A3-FREQ-OUT27 | CRYSTAL OSCILLATOR, CLOCK, 1 MHz - 4 MHz, HCMOS OUTPUT |
| NTHA3JAA3-FREQ-OUT27 | CRYSTAL OSCILLATOR, CLOCK, 1 MHz - 4 MHz, HCMOS OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NAND01GW3B2AN6T | 功能描述:闪存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND01GW3B2AZA1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GW3B2AZA6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GW3B2AZA6E | 功能描述:闪存 NAND MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND01GW3B2AZA6F | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3.3V 1GBIT 128MX8 25US 63VFBGA - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。