- 您现在的位置：买卖IC网 > PDF目录98080 > SII3114CT176 PCI BUS CONTROLLER, PQFP176 PDF资料下载
参数资料
| 型号： | SII3114CT176 |
| 元件分类： | 总线控制器 |
| 英文描述： | PCI BUS CONTROLLER, PQFP176 |
| 封装： | TQFP-176 |
| 文件页数： | 115/127页 |
| 文件大小： | 564K |
| 代理商： | SII3114CT176 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页当前第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页
SiI3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
SiI-DS-0103-D
80
2007 Silicon Image, Inc.
Issue a PIO read/write command to the device following the steps in the “Issue ATA Command” section on page
76.
Read Operation
Wait for a PCI interrupt.
Read the DMA status bits [18:16] of the PCI Bus Master – Channel x register, and check that bit 18 is set
to make sure the interrupt was generated by the expected channel.
If expected channel interrupted, read bits [11:10] of the channel’s Channel x Task File Timing +
Configuration + Status register to determine the cause of the interrupt. Bit 11 is set if the ATA/ATAPI
device has an interrupt pending, bit 10 is set if a virtual DMA operation completed.
If a virtual DMA operation completed,
Write 00H to bits [7:0] of the PCI Bus Master – Channel x register to disable DMA operation.
Write 1 to bits [18:17] of the PCI Bus Master –Channel x register to reset the DMA status and
virtual DMA interrupt bits, and the PCI interrupt.
Check the previously read DMA status bits to ensure the DMA completed successfully.
Because ATA/ATAPI commands that transfer data using PIO can generate several interrupts
during the data transfer phase of the command, a race condition is created between the interrupt
indicating the completion of a virtual DMA operation, and the interrupt from the ATA/ATAPI device
indicating it is ready to perform the next part of the data transfer. To prevent missing an
ATA/ATAPI device interrupt due to this race condition, it is necessary to re-read the channel’s
Channel x Task File Timing + Configuration + Status register after disabling DMA operation and
examining bit 11. If bit 11 is set, the ATA/ATAPI device is interrupting and should be serviced by
following the steps below (assuming that the virtual DMA operation completed successfully).
If the ATA/ATAPI device has interrupted,
Read the device status at bits [31:24] in the Channel x Task File Register 1 register to clear the
device interrupt and determine if there was an error.
Write 1 to bit 18 of the PCI Bus Master – Channel x register to clear the DMA Complete bit
(NOTE: The DMA Complete bit acts as a latched copy of the ATA interrupt line when the channel
is not performing a DMA operation).
If the ATA/ATAPI device is not reporting an error, and DRQ is asserted (bit 27 of Channel x Task
File Register 1), then the device is interrupting to transfer data to the host. To transfer the data,
the DMA registers are setup to only perform that part of the data transfer expected for this
interrupt. The DMA is setup similarly to the way it is when performing a normal read DMA
command, but with one additional step. Before the DMA is enabled, the Channel x Virtual
DMA/PIO Read Ahead Byte Count register must be written with the 32-bit count of the number of
bytes to be transferred for this interrupt.
Repeat the above steps until all data for the read command has been transferred or an error has been
detected.
Write Operation
Poll the Channel x Task File Register 1 bits [31:24] until either bit 27 (DRQ) is set indicating the device is
ready for write data transfer, or bit 24 (ERR) is set indicating the device has detected an error with the
write command.
If no error, and DRQ is asserted (bit 27 of Channel x Task File Register 1), then the device is waiting for
write data transfer. To transfer the data, the DMA registers are setup to only perform that part of the data
transfer expected at this time. For example, a Write Sectors command would expect to transfer 1 sector
(512 bytes), while a Write Multiple command would expect to transfer the lesser of the number of sectors
set by the Set Multiple Mode command or the total number of sectors specified by the Write Multiple
command. The DMA is setup similarly to the way it is when performing a normal write DMA command, but
相关PDF资料 |
PDF描述 |
|---|---|
| SII3114CTU | PCI BUS CONTROLLER, PQFP176 |
| SII3124ACBHU | PCI BUS CONTROLLER, PBGA364 |
| SII3512ECTU128 | PCI BUS CONTROLLER, PQFP128 |
| SII3531ACNU | PCI BUS CONTROLLER, QCC48 |
| SIO10N268-NU | MULTIFUNCTION PERIPHERAL, PQFP128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SII3114CTU | 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述: |
| SII3124A | 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3124ACBHU | 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3132 | 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI Express to 2-Port Serial ATA II Host Controller |
| SII3132CNU | 制造商:Silicon Image Inc 功能描述:PCI Express to Serial ATA Controller 88-Pin QFN |
发布紧急采购，3分钟左右您将得到回复。