参数资料
型号: SII3114CT176
元件分类: 总线控制器
英文描述: PCI BUS CONTROLLER, PQFP176
封装: TQFP-176
文件页数: 13/127页
文件大小: 564K
代理商: SII3114CT176
SiI3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
2007 Silicon Image, Inc.
3
SiI-DS-0103-D
Configuration Read
Configuration Write
Memory Read
Memory Write
All other PCI cycles are ignored by the SiI3114.
As a PCI master, the SiI3114 generates the following PCI bus operations:
Memory Read Multiple
Memory Read
Memory Write
PCI Configuration Space
This section describes how the SiI3114 implements the required PCI configuration register space. The intent of
PCI configuration space definition is to provide an appropriate set of configuration registers that satisfy the needs
of current and anticipated system configuration mechanisms, without specifying those mechanisms or otherwise
placing constraints on their use. These registers allow for:
Full device relocation (including interrupt binding)
Installation, configurations, and booting without user interventions
System address map construction by device-independent software
Figure 1 illustrates the address line assignments during the configuration cycle.
Figure 1. Address Lines During Configuration Cycle
The SiI3114 only responds to Type 0 configuration cycles. Type 1 cycles, which pass a configuration request on
to another PCI bus, are ignored.
The address phase during a SiI3114 configuration cycle indicates the function number and register number being
addressed which can be decoded by observing the status of the address lines AD[31:0].
The value of the signal lines AD[7:2] during the address phase of configuration cycles selects the register of the
configuration space to access. Valid values are between 0 and 15, inclusive. Accessing registers outside this
range results in an all-0s value being returned on reads, and no action being taken on writes.
The Class Code register contains the Class Code, Sub-Class Code, and Register-Level Programming Interface
registers.
All writable bits in the configuration space except offset 44h, 8Ch are reset to their defaults by the hardware reset,
PCI RESET (RST#) asserted. After reset, the SiI3114 is disabled and will only respond to PCI configuration write
and PCI configuration read cycles.
Deviations from the Specification
The SiI3114 product has been developed and tested to the specification listed in this document. As a result of
testing and customer feedback, we may become aware of deviations to the specification that could affect the
component's operation. To ensure awareness of these deviations by anyone considering the use of the SiI3114,
we have included an Errata section at the end of this specification. Please ensure that the Errata section is
31
11 10
8 7
2 1
0
Bit
Number
Don’t Care
Bit
Number
3-Bit
Function
Number
6-Bit
Register
Number
2-Bit
Type
Number
相关PDF资料
PDF描述
SII3114CTU PCI BUS CONTROLLER, PQFP176
SII3124ACBHU PCI BUS CONTROLLER, PBGA364
SII3512ECTU128 PCI BUS CONTROLLER, PQFP128
SII3531ACNU PCI BUS CONTROLLER, QCC48
SIO10N268-NU MULTIFUNCTION PERIPHERAL, PQFP128
相关代理商/技术参数
参数描述
SII3114CTU 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述:
SII3124A 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller
SII3124ACBHU 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller
SII3132 制造商:SILICONIMAGE 制造商全称:SILICONIMAGE 功能描述:PCI Express to 2-Port Serial ATA II Host Controller
SII3132CNU 制造商:Silicon Image Inc 功能描述:PCI Express to Serial ATA Controller 88-Pin QFN