- 您现在的位置：买卖IC网 > PDF目录10942 > SPC5634MF1MMG80 (Freescale Semiconductor)IC MCU FLASH 1.5M 94K 208-PBGA PDF资料下载
参数资料
| 型号： | SPC5634MF1MMG80 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 96/122页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 1.5M 94K 208-PBGA |
| 标准包装： | 90 |
| 系列： | MPC56xx Qorivva |
| 核心处理器： | e200z3 |
| 芯体尺寸： | 32-位 |
| 速度： | 80MHz |
| 连通性： | CAN，EBI/EMI，LIN，SCI，SPI，UART/USART |
| 外围设备： | DMA，POR，PWM，WDT |
| 输入/输出数： | 114 |
| 程序存储器容量： | 1.5MB（1.5M x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 94K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.25 V |
| 数据转换器： | A/D 34x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 208-BGA |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页当前第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页
Electrical characteristics
MPC5634M Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
75
8 VFLASH is only available in the calibration package.
9 Regulator is functional, with derated performance, with supply voltage down to 4.0 V.
10 Multi-voltage pads (type pad_multv_hv) must be supplied with a power supply between 4.75 V and 5.25 V.
11 The slew rate (SRC) setting must be 0b11 when in low-swing mode.
12 While in low-swing mode there are no restrictions in transitioning to high-swing mode.
13 Pin in low-swing mode can accept a 5 V input.
14 Values are pending characterization.
15 Pin in low-swing mode can accept a 5 V input.
16 Characterization based capability:
IOH_S = {6, 11.6} mA and IOL_S = {9.2, 17.7} mA for {slow, medium} I/O with VDDEH=4.5 V;
IOH_S = {2.8, 5.4} mA and IOL_S = {4.2, 8.1} mA for {slow, medium} I/O with VDDEH=3.0 V
17 Characterization based capability:
IOH_F = {12, 20, 30, 40} mA and IOL_F = {24, 40, 50, 65} mA for {00, 01,10, 11} drive mode with VDDE=3.0 V;
IOH_F = {7, 13, 18, 25} mA and IOL_F = {18, 30, 35, 50} mA for {00, 01, 10, 11} drive mode with VDDE=2.25 V;
IOH_F = {3, 7, 10, 15} mA and IOL_F = {12, 20, 27, 35} mA for {00, 01, 10, 11} drive mode with VDDE=1.62 V
18 All VOL/VOH values 100% tested with ± 2 mA load.
19 Run mode as follows:
System clock = 40/60/80 MHz + FM 2%
Code executed from flash memory
ADC0 at 16 MHz with DMA enabled
ADC1 at 8 MHz
eMIOS pads toggle in PWM mode with a rate between 100 kHz and 500 kHz
eTPU pads toggle in PWM mode with a rate between 10 kHz and 500 kHz
CAN configured for a bit rate of 500 kHz
DSPI configured in master mode with a bit rate of 2 MHz
eSCI transmission configured with a bit rate of 100 kHz
20 Bypass mode, system clock at 1 MHz (using system clock divider), PLL shut down, CPU running simple executive
code, 4 x ADC conversion every 10 ms, 2 × PWM channels at 1 kHz, all other modules stopped.
21 Bypass mode, system clock at 1 MHz (using system clock divider), CPU stopped, PIT running, all other modules
stopped.
22 When using the internal regulator only, a bypass capacitor should be connected to this pin. External circuits should
not be powered by the internal regulator. The internal regulator can be used as a reference for an external debugger.
23 Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a
particular I/O segment, and the voltage of the I/O segment. See Table 23 for values to calculate power dissipation for
specific operation. The total power consumption of an I/O segment is the sum of the individual power consumptions
for each pin on the segment.
24 Absolute value of current, measured at VIL and VIH.
25 Weak pull up/down inactive. Measured at VDDE = 3.6 V and VDDEH = 5.25 V. Applies to pad types: fast (pad_fc).
26 Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half
for each 8 to 12 oC, in the ambient temperature range of 50 to 125 oC. Applies to pad types: pad_a and pad_ae.
27 Applies to CLKOUT, external bus pins, and Nexus pins.
28 Applies to the FCK, SDI, SDO, and SDS pins.
29 This programmable option applies only to eQADC differential input channels and is used for biasing and sensor
diagnostics.
30 When the pull-up and pull-down of the same nominal 200 K or 100 K value are both enabled, assuming no
interference from external devices, the resulting pad voltage will be 0.5*VDDE ±2.5%
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23W-CU-S | CONVERTER MOD DC/DC 5.5V 200W |
| VI-23V-CU-S | CONVERTER MOD DC/DC 5.8V 200W |
| MC9328MXLCVP15 | IC MCU I.MXL 150MHZ 225-MAPBGA |
| SPC5604PEF0MLL6 | IC MCU 32BIT 512KB FLASH 100LQFP |
| S912XDP512J1MAL | IC MCU FLASH 112-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPC5634MF2MLQ80 | 制造商:Freescale Semiconductor 功能描述:SPC5634MF2MLQ80 - Bulk |
| SPC5634MF2MLQ80R | 制造商:Freescale Semiconductor 功能描述:1.5M FLASH,94K RAM,E200Z335 - Tape and Reel |
| SPC5634MF2MLU80 | 制造商:Freescale Semiconductor 功能描述:QORIVVA 32-BIT MCU, POWER ARCH CORE, 1.5MB FLASH, 80MHZ, -40 - Trays 制造商:Freescale Semiconductor 功能描述:IC MCU 32BIT 1.5MB FLASH 176QFP |
| SPC5634MF2MLU80R | 制造商:Freescale Semiconductor 功能描述:SPC5634MF2MLU80R - Tape and Reel |
| SPC5634MF2MMG80 | 制造商:Freescale Semiconductor 功能描述:QORIVVA 32-BIT MCU, POWER ARCH, 1.5MB FLASH, 80MHZ, -40/+125 - Trays 制造商:Freescale Semiconductor 功能描述:IC MCU 32BIT 1.5MB FLASH 208BGA |
发布紧急采购，3分钟左右您将得到回复。