- 您现在的位置：买卖IC网 > PDF目录98145 > ST72E85A5G0 (STMICROELECTRONICS) 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 PDF资料下载
参数资料
| 型号： | ST72E85A5G0 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 |
| 封装： | WINDOWED, CERAMIC, QFP- 80 |
| 文件页数： | 66/117页 |
| 文件大小： | 748K |
| 代理商： | ST72E85A5G0 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页当前第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页
52/117
ST7285C
SERIAL PERIPHERAL INTERFACE(Cont’d)
The second collision mode is defined by the CPHA
control bit being set. With the CPHA bit set, the
Slave device will be receiving a clock (SCK) edge
prior to the latch of the first data transfer. This first
clock edge will freeze the data in the Slave device
I/O register and allow the msb on to the external
MISO pin of the Slave device. A logic low state on
the SS pin enables the Slave device, however,
data is not output on the MISO pin until the first
edge of the data transfer clock. The WCOL bit will
only be set if the I/O register is accessed while a
transfer is taking place. In this second collision
mode, a Master device can hold a Slave device’s
SS pin low during the transfer of several bytes of
data without this causing any problems.
Unlike other SPI interfaces, there is no special
case of collision which remains undetected by
the WCOL bits. The WCOL bit is TOTALLY reli-
able with regard to collision detection.
Since the Slave device is operating asynchronous-
ly with the Master device, the WCOL bit may be
used as an indicator of a collision occurence. This
helps alleviate the user from a strict real-time pro-
gramming effort. The WCOL is cleared on Reset.
Bit-4 = MODF
Mode Fault flag
The function of the mode fault flag is defined for
the Master mode (device). If the device is a Slave
device the MODF bit will be prevented from tog-
gling from reset to set; however, this does not pre-
vent the device from being in the Slave mode with
the MODF bit set.
The MODF bit is normally reset, and is set only
when the Master device has itsSS pin pulled low.
Toggling the MODF bit to the set state affects the
internal Serial Peripheral Interface (SPI) system in
the following ways:
a) MODF is set and SPI interrupt is generated if
SPIE is set.
b) The SPE bit is forced to a reset state. This
blocks all output from the device and disables the
SPI system.
c) The MSTR bit is forced to a reset state, thus
forcing the device into the Slave mode.
Clearing the MODF is accomplished by a software
sequence which accesses the Serial Peripheral
Status Register while MODF is set, followed by a
write to the Serial Peripheral Control Register.
To avoid multiple Slave conflicts in a system com-
prising several MCUs, the SS pin must be pulled
high during the clearing sequence of MODF. Con-
trol bits SPE and MSTR may be restored to their
original set state during this clearing sequence, or
after the MODF bit has been cleared. Hardware
does not allow the user to set the SPE and MSTR
bits while MODF is set, unless this occurs during
the proper clearing sequence. The MODF flag bit
indicates the possible occurrence of a Multimaster
conflict for system control, and allows proper exit
from normal system operation to Reset or to a de-
fault system state. The MODF bit is cleared on Re-
set.
相关PDF资料 |
PDF描述 |
|---|---|
| ST72F321J9T7 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T3 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T1 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J9T5 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F324BJ6B6 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP42 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST72F260G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST72F260G1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI/I2C/SCI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST72F260G1M6/TR | 功能描述:8位微控制器 -MCU 8B MCU FLASH OR ROM MEMORY RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST72F262G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST72F262G1B6 | 功能描述:8位微控制器 -MCU 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。