参数资料
型号: ZL50114GAG
厂商: XILINX INC
元件分类: 通信及网络
英文描述: SPECIALTY TELECOM CIRCUIT, PBGA552
封装: 35 X 35 MM, 1.27 MM PITCH, PLASTIC, MS-034, BGA-552
文件页数: 7/113页
文件大小: 2004K
代理商: ZL50114GAG
ZL50110/11/12/14
Data Sheet
104
Zarlink Semiconductor Inc.
13.0
Design and Layout Guidelines
This guide will provide information and guidance for PCB layouts when using the ZL50110/11/12/14. Specific areas
of guidance are:
High Speed Clock and Data, Outputs and Inputs
CPU_TA Output
13.1
High Speed Clock & Data Interfaces
On the ZL50110/11/12/14 series of devices there are four high-speed data interfaces that need consideration when
laying out a PCB to ensure correct termination of traces and the reduction of crosstalk noise. The interfaces being:
External Memory Interface
GMAC Interfaces
TDM Interface
CPU Interface
It is recommended that the outputs are suitably terminated using a series termination through a resistor as close to
the output pin as possible. The purpose of the series termination resistor is to reduce reflections on the line. The
value of the series termination and the length of trace the output can drive will depend on the driver output
impedance, the characteristic impedance of the PCB trace (recommend 50 ohm), the distributed trace capacitance
and the load capacitance. As a general rule of thumb, if the trace length is less than 1/6th of the equivalent length of
the rise and fall times, then a series termination may not be required.
the equivalent length of rise time = rise time (ps) / delay (ps/mm)
For example:
Typical FR4 board delay = 6.8 ps/mm
Typical rise/fall time for a ZL50110/11/12/14 output = 2.5 ns
critical track length = (1/6) x (2500/6.8) = 61 mm
Therefore tracks longer than 61 mm will require termination.
As a signal travels along a trace it creates a magnetic field, which induces noise voltages in adjacent traces, this is
crosstalk. If the crosstalk is of sufficiently strong amplitude, false data can be induced in the trace and therefore it
should be minimized in the layout. The voltage that the external fields cause is proportional to the strength of the
field and the length of the trace exposed to the field. Therefore to minimize the effect of crosstalk some basic
guidelines should be followed.
First, increase separation of sensitive signals, a rough rule of thumb is that doubling the separation reduces the
coupling by a factor of four. Alternatively, shield the victim traces from the aggressor by either routing on another
layer separated by a power plane (in a correctly decoupled design the power planes have the same AC potential) or
by placing guard traces between the signals usually held ground potential.
Particular effort should be made to minimize crosstalk from ZL50110/11/12/14 outputs and ensuring fast rise time to
these inputs.
In Summary:
Place series termination resistors as close to the pins as possible
Minimize output capacitance
Keep common interface traces close to the same length to avoid skew
Protect input clocks and signals from crosstalk
相关PDF资料
PDF描述
ZL50232GD DATACOM, ISDN ECHO CANCELLER, PBGA208
ZL50233/GDG DATACOM, ISDN ECHO CANCELLER, PBGA208
ZL50408GDC DATACOM, LAN SWITCHING CIRCUIT, PBGA208
ZL50408GDG2 DATACOM, LAN SWITCHING CIRCUIT, PBGA208
ZL50418GKG2 DATACOM, LAN SWITCHING CIRCUIT, PBGA553
相关代理商/技术参数
参数描述
ZL50114GAG2 制造商:Microsemi Corporation 功能描述:CESOP PROCESSOR 552BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 128CH 552PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 128CH 552PBGA
ZL50115 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:32, 64 and 128 Channel CESoP Processors
ZL50115GAG 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 324BGA - Trays 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 32CH 324PBGA
ZL50115GAG2 制造商:Microsemi Corporation 功能描述:PB FREE 1 TDM + 1 ETHERNET - Trays 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 32CH 324PBGA
ZL50116 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:32, 64 and 128 Channel CESoP Processors