- 您现在的位置：买卖IC网 > PDF目录1900 > ADUC7032BSTZ-8V-RL (Analog Devices Inc)IC BATTERY SENSOR PREC 48-LQFP PDF资料下载
参数资料
| 型号： | ADUC7032BSTZ-8V-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 76/128页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY SENSOR PREC 48-LQFP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI，UART/USART |
| 外围设备： | POR，PSM，温度传感器，WDT |
| 输入/输出数： | 9 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 标准包装 |
| 其它名称： | ADUC7032BSTZ-8V-RLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 51 of 128
ADC Mode Register :
Name :
ADCMDE
Address :
0xFFFF0508
Default Value :
0x00
Access :
Read/Write
Function :
The ADC Mode MMR is an 8-bit register that configures the mode .of operation of the ADC sub-system
Table 23 : ADCMDE MMR Bit Designations
Bit
Description
7
Not Used
This bit is reserved for future functionality and be written as 0 by user code
6
20K
resistor select:
This bit is set to 1 to select the 20 K
resistor as shown in Figure 18
This bit is set to 0 to select the direct path to ground as shown in
Figure 18 ( Default ).
5
Low Power Mode Reference Select:
This bit is set to 1 to enable the Precision Voltage Reference in ADC Low Power Mode. This will increase current consumption.
This bit is set to 0 to enable the Low Power Voltage Reference in ADC Low Power Mode ( Default ).
4-3
ADC Power Mode Configuration
0, 0
ADC Normal Mode
If enabled, the ADC will operate with normal current consumption yielding optimum electrical performance
0, 1
ADC Low Power Mode
If enabled, the I-ADC will operate with reduced current consumption. This limitation is current consumption is
achieved, (at the expense of ADC noise performance) by fixing the gain to 128 and using the on-chip low power
(131kHz) oscillator to drive the ADC circuits directly.
1, 0
ADC Low Power-Plus Mode
If enabled, the ADC will again operate with reduced current consumption. In this mode the gain is fixed to 512 and
the current consumed is 200uA (approx.) more than ADC low Power Mode above. The additional current consumed
also ensures ADC noise performance is better than that achieved in ADC Low Power Mode.
1, 1
Not Defined
2-0
ADC Operation Mode Configuration
0, 0, 0 ADC Power-Down Mode
All ADC circuits (including internal reference) are powered-down
0, 0, 1 ADC Continuous Conversion Mode
In this mode, any enabled ADC will continuously convert.
0, 1, 0 ADC Single Conversion Mode
In this mode, any enabled ADC will perform a single conversion. The ADC will enter Idle Mode once the single
shot conversion is complete. A single conversion will take 2/3 ADC clock cycles depending on the CHOP mode.
0, 1, 1 ADC IDLE Mode
In this Mode, the ADC is fully powered on but is held in RESET
1, 0, 0 ADC Self-Offset Calibration
In this mode, an offset calibration is performed on any enabled ADC using an internally generated 0V. The
calibration is carried out at the user programmed ADC settings, therefore, as with a normal
single ADC
conversion, it will take 2/3 ADC conversion cycles before a fully settled calibration result is ready. The calibration
result is automatically written to the ADCxOF MMR of the respective ADC. The ADC returns to IDLE Mode and the
Calibration and Conversion Ready status bits are set at the end of an offset calibration cycle.
1, 0, 1 ADC Self Gain Calibration
In this mode, a gain calibration against an internal reference voltage is performed on all enabled ADCs. A gain
calibration is a 2 stage process and takes twice the time of an offset calibration. The calibration result is
automatically written to the ADCxGN MMR of the respective ADC. The ADC returns to IDLE Mode and the calibration
and Conversion Ready status bits are set at the end of an gain calibration cycle. An ADC self gain calibration should
only be carried out on the Current Channel ADC while pre-programmed, factory calibration coefficients (downloaded
automatically from internal Flash) should be used for voltage temperature measurements. If an external NTC is used,
an ADC Self Calibration should be done on the temperature channel.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7034BCPZ | IC MCU FLASH 32K ANLG IO 48LFCSP |
| ADUC7036CCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| ADUC7039BCP6Z-RL | IC MCU ARM7 BATT SENSER 32LFCSP |
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7033 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
| ADUC7033BCPZ-8L | 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays |
| ADUC7033BCPZ-8L-RL | 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel |
| ADUC7033BSTZ-88 | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| ADUC7033BSTZ-88-RL | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。