- 您现在的位置：买卖IC网 > PDF目录1914 > DS2196LN+ (Maxim Integrated Products)IC FRAMER DUAL T1 LIU 100-LQFP PDF资料下载
参数资料
| 型号： | DS2196LN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 105/157页 |
| 文件大小： | 0K |
| 描述： | IC FRAMER DUAL T1 LIU 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 控制器类型： | T1 调帧器 |
| 接口： | 并行/串行 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 85mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页当前第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
DS2196
51 of 157
7. STATUS AND INFORMATION REGISTERS
Found in each Framer/Formatter is a set of nine registers that contain information on the current real time
status of the DS2196, Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Registers 1
to 3 (RIR1/RIR2/RIR3) and a set of four registers for the onboard HDLC and BOC controller for the
FDL. BERT generator and receiver status is contained in the BERT Information Register (BIR). The
specific details on the registers pertaining to the BERT and FDL functions are covered in Section 15 and
18 but they operate the same as the other status registers in the DS2196 and this operation is described
below.
When a particular event has occurred (or is occurring), the appropriate bit in 1 of these nine registers will
be set to a 1. All of the bits in SR1, SR2, RIR1, RIR2, and RIR3 registers operate in a latched fashion.
This means that if an event or an alarm occurs and a bit is set to a 1 in any of the registers, it will remain
set until the user reads that bit. The bit will be cleared when it is read and it will not be set again until the
event has occurred again (or in the case of the RBL, RYEL, LRCL or FRCL, and RLOS alarms, the bit
will remain set if the alarm is still present). There are bits in the four FDL status registers that are not
latched and these bits are listed in Section 18.
The user will always precede a read of any of the nine registers with a write. The byte written to the
register will inform the DS2196 which bits the user wishes to read and have cleared. The user will write
a byte to one of these registers, with a 1 in the bit positions he or she wishes to read and a 0 in the bit
positions he or she does not wish to obtain the latest information on. When a 1 is written to a bit location,
the read register will be updated with the latest information. When a 0 is written to a bit position, the read
register will not be updated and the previous value will be held. A write to the status and information
registers will be immediately followed by a read of the same register. The read result should be logically
AND’ed with the mask byte that was just written and this value should be written back into the same
register to insure that bit does indeed clear. This second write step is necessary because the alarms and
events in the status registers occur asynchronously in respect to their access via the parallel port. This
write–read– write scheme allows an external microcontroller or microprocessor to individually poll
certain bits without disturbing the other bits in the register. This operation is key in controlling the
DS2196 with higher–order software languages.
The SR1, SR2, HSR and BIR registers have the unique ability to initiate a hardware interrupt via the INT
output pin. Each of the alarms and events in the SR1, SR2, HSR and BIR can be either masked or
unmasked from the interrupt pin via the Interrupt Mask Register 1 (IMR1), Interrupt Mask Register 2
(IMR2), HDLC Interrupt Mask Register (HIMR) and BERT Control Register (BC1) respectively. The
BC1 register is covered in Section 15. The HIMR register is covered in Section 18.
The interrupts caused by alarms in SR1 (namely RYEL, LRCL or RCL, RBL, and RLOS) act differently
than the interrupts caused by events in SR1 and SR2 (namely LUP, LDN, LSPARE, LOTC, RMF, TMF,
SEC, RFDL, TFDL, RMTCH, RAF, and LORC) and FIMR. The alarm caused interrupts will force the
INT pin low whenever the alarm changes state (i.e., the alarm goes active or inactive according to the
set/clear criteria in Table 7–2). The INT pin will be allowed to return high (if no other interrupts are
present) when the user reads the alarm bit that caused the interrupt to occur even if the alarm is still
present.
The event caused interrupts will force the INT pin low when the event occurs. The INT pin will be
allowed to return high (if no other interrupts are present) when the user reads the event bit that caused the
interrupt to occur.
ISR: INTERRUPT STATUS REGISTER (Address = 0E Hex)
相关PDF资料 |
PDF描述 |
|---|---|
| DS21FF42 | IC FRAMER T1 4X4 16CH 300-BGA |
| DS21FF44 | IC FRAMER E1 4X4 16CH 300-BGA |
| DS21FT44N+ | IC FRAMER 4X4 16CH 300-BGA |
| DS21Q352B | IC TXRX QUAD T1/E1 3.3V 256-BGA |
| DS21Q41BT | IC FRAMER T1 QUAD 128-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2196LN+ | 功能描述:网络控制器与处理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS219T | 功能描述:烙铁 DESOLDERING HEAD RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included |
| DS21E352 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21E352N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21E354 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。