- 您现在的位置：买卖IC网 > PDF目录1917 > DSPB56362AG120 (Freescale Semiconductor)IC DSP 24BIT AUD 120MHZ 144-LQFP PDF资料下载
参数资料
| 型号： | DSPB56362AG120 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/152页 |
| 文件大小： | 0K |
| 描述： | IC DSP 24BIT AUD 120MHZ 144-LQFP |
| 标准包装： | 60 |
| 系列： | DSP56K/Symphony |
| 类型： | 音频处理器 |
| 接口： | 主机接口，I²C，SAI，SPI |
| 时钟速率： | 120MHz |
| 非易失内存： | ROM（126 kB） |
| 芯片上RAM： | 42kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 3.30V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-LQFP（20x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页
Host Port Considerations
DSP56362 Technical Data, Rev. 4
Freescale Semiconductor
5-5
5.4.3
Frequency Jitter Performance
The frequency jitter of the PLL is defined as the variation of the frequency of CLKOUT. For small MF
(MF < 10) this jitter is smaller than 0.5%. For mid-range MF (10 < MF < 500) this jitter is between 0.5%
and approximately 2%. For large MF (MF > 500), the frequency jitter is 2–3%.
5.4.4
Input (EXTAL) Jitter Requirements
The allowed jitter on the frequency of EXTAL is 0.5%. If the rate of change of the frequency of EXTAL
is slow (i.e., it does not jump between the minimum and maximum values in one cycle) or the frequency
of the jitter is fast (i.e., it does not stay at an extreme value for a long time), then the allowed jitter can be
2%. The phase and frequency jitter performance results are only valid if the input jitter is less than the
prescribed values.
5.5
Host Port Considerations
Careful synchronization is required when reading multi-bit registers that are written by another
asynchronous system. This synchronization is a common problem when two asynchronous systems are
connected, as they are in the host interface. The following paragraphs present considerations for proper
operation.
5.5.1
Host Programming Considerations
Unsynchronized Reading of Receive Byte Registers
—When reading the receive byte registers,
receive register high (RXH), receive register middle (RXM), or receive register low (RXL), the
host interface programmer should use interrupts or poll the receive register data full (RXDF) flag
that indicates whether data is available. This ensures that the data in the receive byte registers will
be valid.
Overwriting Transmit Byte Registers
—The host interface programmer should not write to the
transmit byte registers, transmit register high (TXH), transmit register middle (TXM), or transmit
register low (TXL), unless the transmit register data empty (TXDE) bit is set, indicating that the
transmit byte registers are empty. This ensures that the transmit byte registers will transfer valid
data to the host receive (HRX) register.
Synchronization of Status Bits from DSP to Host
—HC, HOREQ, DMA, HF3, HF2, TRDY,
TXDE, and RXDF status bits are set or cleared from inside the DSP and read by the host processor
(refer to the user’s manual for descriptions of these status bits). The host can read these status bits
very quickly without regard to the clock rate used by the DSP, but the state of the bit could be
changing during the read operation. This is not generally a system problem, because the bit will be read
correctly in the next pass of any host polling routine.
However, if the host asserts HEN for more than timing number 31, with
a minimum cycle time of timing number 31 + 32, then these status bits are guaranteed to be
stable. Exercise care when reading status bits HF3 and HF2 as an encoded pair. If the DSP
changes HF3 and HF2 from 00 to 11, there is a small probability that the host could read the bits
during the transition and receive 01 or 10 instead of 11. If the combination of HF3 and HF2 has
相关PDF资料 |
PDF描述 |
|---|---|
| DSPB56364AF100 | IC DSP 24BIT AUD 100MHZ 100-LQFP |
| DSPB56366AG120 | IC DSP 24BIT AUD 120MHZ 144-LQFP |
| DSPB56367AG150 | IC DSP 24BIT 150MHZ 144-LQFP |
| DSPB56371AF180 | IC DSP 24BIT 180MHZ 80-LQFP |
| DSPB56374AEC | IC DSP 24BIT 150MHZ 52-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DSPB56362AG120 | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor |
| DSPB56362PV100 | 制造商:Rochester Electronics LLC 功能描述:DIGITAL AUDIO DSP - Bulk |
| DSPB56362PV120 | 制造商:Rochester Electronics LLC 功能描述:DIGITAL AUDIO DSP - Bulk |
| DSPB56364AF100 | 功能描述:数字信号处理器和控制器 - DSP, DSC DSP56364 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPB56364FU100 | 制造商:Rochester Electronics LLC 功能描述:24 BIT AUDIO DSP - Bulk 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
发布紧急采购，3分钟左右您将得到回复。