- 您现在的位置：买卖IC网 > PDF目录97874 > EC103D175 Thyristor Product Catalog PDF资料下载
参数资料
| 型号： | EC103D175 |
| 英文描述： | Thyristor Product Catalog |
| 中文描述： | 晶闸管产品目录 |
| 文件页数： | 86/224页 |
| 文件大小： | 2697K |
| 代理商： | EC103D175 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页当前第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页
AN1007
Application Notes
http://www.teccor.com
AN1007 - 4
2002 Teccor Electronics
+1 972-580-7777
Thyristor Product Catalog
Figure AN1007.8
Optocoupler Circuit for Lower Current Inductive
Loads (Triac or Alternistor)
In this circuit, the series gate resistors are increased to 180
each, since a 240 V line is applied. Note that the load is placed
on the MT1 side of the power triac to illustrate that load place-
ment is not important for the circuit to function properly.
Also note that with standard U.S. residential 240 V home wiring,
both sides of the line are hot with respect to ground (no neutral).
Therefore, for some 240 V line applications, it will be necessary
to have a triac switch circuit in both sides of the 240 V line input.
If an application requires back-to-back SCRs instead of a triac or
alternistor, the circuit shown in Figure AN1007.9 may be used.
Figure AN1007.9
Optocoupled Circuit for Heavy-duty Inductive Loads
All application comments and recommendations for optocoupled
switches apply to this circuit. However, the snubber network can
be applied only across the SCRs as shown in the illustration. The
optocoupler should be chosen for best noise immunity. Also, the
voltage rating of the optocoupler output triac must be equal to or
greater than the voltage rating of SCRs.
Summary of Random Turn-on Relays
As shown in Figure AN1007.10, if the voltage across the load is
to be phase controlled, the input control circuitry must be syn-
chronized to the line frequency and the trigger pulses delayed
from zero crossing every half cycle. If the series gate resistor is
chosen to limit the peak current through the opto-driver to less
than 1 A, then on a 120 V ac line the peak voltage is 170 V;
therefore, the resistor is 180
. On a 240 V ac line the peak volt-
age is 340 V; therefore, the resistor should be 360
. These gate
pulses are only as long as the device takes to turn on (typically,
5 s to 6 s); therefore, 0.25 W resistor is adequate.
Figure AN1007.10
Random Turn-on Triac Driver
Select the triac for the voltage of the line being used, the current
through the load, and the type of load. Since the peak voltage of
a 120 V ac line is 170 V, you would choose a 200 V (MIN) device.
If the application is used in an electrically noisy industrial envi-
ronment, a 400 V device should be used. If the line voltage to be
controlled is 240 V ac with a peak voltage of 340 V, then use at
least a 400 V rated part or 600 V for more design margin. Selec-
tion of the voltage rating of the opto-driver must be the same or
higher than the rating of the power triac. In electrically noisy
industrial locations, the dv/dt rating of the opto-driver and the
triac must be considered.
The RMS current through the load and main terminals of the triac
should be approximately 70% of the maximum rating of the
device. However, a 40 A triac should not be chosen to control a
1 A load due to low latching and holding current requirements.
Remember that the case temperature of the triac must be main-
tained at or below the current versus temperature curve specified
on its data sheet. As with all semiconductors the lower the case
temperature the better the reliability. Opto-driven gates normally
do not use a sensitive gate triac. The opto-driver can supply up to
1 A gate pulses and less sensitive gate triacs have better dv/dt
capability. If the load is resistive, it is acceptable to use a stan-
dard triac. However, if the load is a heavy inductive type, then an
alternistor triac, or back-to-back SCRs as shown in Figure
AN1007.9, is recommended. A series RC snubber network may
or may not be necessary when using an alternistor triac. Nor-
mally a snubber network is not needed when using an alternistor
because of its high dv/dt and dv/dt(c) capabilities. However,
latching network as described in Figure AN1007.8 may be
needed for low current load variations.
Zero Crossing Turn-on, Normally Open
Relay Circuits
When a power circuit is mechanically switched on and off
mechanically, generated high-frequency components are gener-
ated that can cause interference problems such as RFI. When
power is initially applied, a step function of voltage is applied to
the circuit which causes a shock excitation. Random switch
opening stops current off, again generating high frequencies. In
addition, abrupt current interruption in an inductive circuit can
lead to high induced-voltage transients.
The latching characteristics of thyristors are ideal for eliminating
interference problems due to current interruption since these
devices can only turn off when the on-state current approaches
zero, regardless of load power factor.
On the other hand, interference-free turn-on with thyristors
requires special trigger circuits. It has been proven experimen-
6
Rin
Vcc
1
180
G
240 V ac
MT2
MT1
2
180
0.1 F
3
4
5
0.047 F
3.3 k
Load
Rin
Vcc
1
G
120 V ac
2
3
0.1
F
Load
6
4
5
100
K
A
100
G
A
K
NS-SCR
NS-
SCR
Triac or
Alternistor
MT2
0.1
f
100
Load
MT1
Hot
Neutral
120/240 V ac
G
180
for 120 V ac
360
for 240 V ac
Input
Rin
1
6
5
4
3
2
Load could be here
instead of lower location
相关PDF资料 |
PDF描述 |
|---|---|
| EC103D1 | Sensitive SCRs |
| EC103D | Sensitive SCRs |
| EC103D2 | Sensitive SCRs |
| EC103D3 | Sensitive SCRs |
| EC103M1 | PC 8C 8#20 PIN RECP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EC103D1AP | 功能描述:SEN SCR 400V .8A 12A TO92 RoHS:否 类别:分离式半导体产品 >> SCR - 单个 系列:- 其它有关文件:X00619 View All Specifications 产品目录绘图:SCR TO-92 Package 标准包装:1 系列:- SCR 型:灵敏栅极 电压 - 断路:600V 电压 - 栅极触发器 (Vgt)（最大）:800mV 电压 - 导通状态 (Vtm)（最大）:1.35V 电流 - 导通状态 (It (AV))（最大）:500mA 电流 - 导通状态 (It (RMS))（最大）:800mA 电流 - 栅极触发电流 (Igt)（最大）:200µA 电流 - 维持(Ih):5mA 电流 - 断开状态（最大）:1µA 电流 - 非重复电涌，50、60Hz (Itsm):9A，10A 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-226-3、TO-92-3（TO-226AA）成形引线 供应商设备封装:TO-92-3 包装:剪切带 (CT) 产品目录页面:1554 (CN2011-ZH PDF) 其它名称:497-9067-1 |
| EC103D1RP | 功能描述:SCR 400V .8A 12uA RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| EC103D1WX | 制造商:NXP Semiconductors 功能描述:1000 制造商:NXP Semiconductors 功能描述:EC103D1W/SC-73/REEL7// - Tape and Reel 制造商:NXP Semiconductors 功能描述:SCR SENS GATE 400V SC-73 制造商:NXP Semiconductors 功能描述:SCRs 400v Sc-73 Scr Sens Gate |
| EC103D2 | 功能描述:SCR 400V .8A 50uA Sensing RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| EC103D275 | 功能描述:SCR 400V .8A 50uA RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。