- 您现在的位置：买卖IC网 > PDF目录69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF资料下载
参数资料
| 型号： | MCC68HC711D3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封装： | DIE |
| 文件页数： | 120/157页 |
| 文件大小： | 2252K |
| 代理商： | MCC68HC711D3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页当前第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
Resets, Interrupts, and Low-Power Modes
Low-Power Operation
MC68HC711D3 — Rev. 2
Data Sheet
MOTOROLA
Resets, Interrupts, and Low-Power Modes
65
4.4 Low-Power Operation
The M68HC11 Family of microcontroller units (MCU) has two programmable low
power-consumption modes: stop and wait. In the wait mode, the on-chip oscillator
remains active. In the stop mode, the oscillator is stopped. This subsection
describes these two low power-consumption modes.
4.4.1 Stop Mode
The STOP instruction places the MCU in its lowest power-consumption mode,
provided the S bit in the CCR is cleared. In this mode, all clocks are stopped,
thereby halting all internal processing.
To exit the stop mode, a low level must be applied to either the IRQ, XIRQ, or
RESET pin. An external interrupt used at IRQ is only effective if the I bit in the CCR
is cleared. An external interrupt applied at the XIRQ input is effective, regardless
of the setting of the X bit of the CCR. However, the actual recovery sequence
differs, depending on the X bit setting. If the X bit is cleared, the MCU starts with
the stacking sequence leading to the normal service of the XIRQ request. If the X
bit is set, the processing always continues with the instruction immediately
following the STOP instruction. A low input to the RESET pin always results in an
exit from the stop mode, and the start of MCU operations is determined by the reset
vector.
The CPU will not exit stop mode correctly when interrupted by IRQ or XIRQ if the
instruction preceding STOP is a column 4 or 5 accumulator inherent (opcodes $4X
and $5X) instruction, such as NEGA, NEGB, COMA, COMB, etc. These
single-byte, two-cycle instructions must be followed by an NOP, then the STOP
command. If reset is used to exit stop mode, the CPU will respond properly.
A restart delay is required if the internal oscillator is being used. The delay allows
the oscillator to stabilize when exiting the stop mode. If a stable external oscillator
is being used, the delay (DLY) bit in the OPTION register can be cleared to bypass
the delay. If the DLY bit is clear, the RESET pin would not normally be used to exit
the stop mode. The reset sequence sets the DLY bit, and the restart delay would
be reimposed.
1 0 0 1
Timer input capture 2
1 0 1 0
Timer input capture 3
1 0 1 1
Timer output compare 1
1 1 0 0
Timer output compare 2
1 1 0 1
Timer output compare 3
1 1 1 0
Timer output compare 4
1 1 1 1
Timer input capture 4/output compare 5
Table 4-4. Highest Priority Interrupt Selection (Continued)
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
发布紧急采购，3分钟左右您将得到回复。