- 您现在的位置：买卖IC网 > PDF目录69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF资料下载
参数资料
| 型号： | MCC68HC711D3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封装： | DIE |
| 文件页数： | 5/157页 |
| 文件大小： | 2252K |
| 代理商： | MCC68HC711D3 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
Programmable Timer
Data Sheet
MC68HC711D3 — Rev. 2
102
Programmable Timer
MOTOROLA
8.4 Output Compare (OC)
Use the output compare (OC) function to program an action to occur at a specific
time — when the 16-bit counter reaches a specified value. For each of the five
output compare functions, there is a separate 16-bit compare register and a
dedicated 16-bit comparator. The value in the compare register is compared to the
value of the free-running counter on every bus cycle. When the compare register
matches the counter value, an output compare status flag is set. The flag can be
used to initiate the automatic actions for that output compare function.
To produce a pulse of a specific duration, write to the output compare register a
value representing the time the leading edge of the pulse is to occur. The output
compare circuit is configured to set the appropriate output either high or low,
depending on the polarity of the pulse being produced. After a match occurs, the
output compare register is reprogrammed to change the output pin back to its
inactive level at the next match. A value representing the width of the pulse is
added to the original value, and then is written to the output compare register.
Because the pin state changes occur at specific values of the free-running counter,
the pulse width can be controlled accurately at the resolution of the free-running
counter, independent of software latencies. To generate an output signal of a
specific frequency and duty cycle, repeat this pulse-generating procedure.
There are four 16-bit read/write output compare registers: TOC1, TOC2, TOC3,
and TOC4, and the TI4/O5 register, which functions under software control as
either IC4 or OC5. Each of the OC registers is set to $FFFF on reset. A value
written to an OC register is compared to the free-running counter value during each
E-clock cycle. If a match is found, the particular output compare flag is set in timer
interrupt flag register 1 (TFLG1). If that particular interrupt is enabled in the timer
interrupt mask register 1 (TMSK1), an interrupt is generated. In addition to an
interrupt, a specified action can be initiated at one or more timer output pins. For
OC5–OC2, the pin action is controlled by pairs of bits (OMx and OLx) in the TCTL1
register. The output action is taken on each successful compare, regardless of
whether the OCxF flag in the TFLG1 register was previously cleared.
OC1 is different from the other output compares in that a successful OC1 compare
can affect any or all five of the OC pins. The OC1 output action taken when a match
is found is controlled by two 8-bit registers with three bits unimplemented: the
output compare 1 mask register, OC1M, and the output compare 1 data register,
OC1D. OC1M specifies which port A outputs are to be used, and OC1D specifies
what data is placed on these port pins.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
发布紧急采购，3分钟左右您将得到回复。