- 您现在的位置：买卖IC网 > PDF目录69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF资料下载
参数资料
| 型号： | MCC68HC711D3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封装： | DIE |
| 文件页数： | 131/157页 |
| 文件大小： | 2252K |
| 代理商： | MCC68HC711D3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页当前第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
Serial Communications Interface (SCI)
Receive Operation
MC68HC711D3 — Rev. 2
Data Sheet
MOTOROLA
Serial Communications Interface (SCI)
75
6.4 Receive Operation
During receive operations, the transmit sequence is reversed. The serial shift
register receives data and transfers it to a parallel receive data register (SCDR) as
a complete word. Refer to Figure 6-2. This double-buffered operation allows a
character to be shifted in serially while another character is already in the SCDR.
An advanced data recovery scheme distinguishes valid data from noise in the
serial data stream. The data input is selectively sampled to detect receive data, and
a majority voting circuit determines the value and integrity of each bit.
6.5 Wakeup Feature
The wakeup feature reduces SCI service overhead in multiple receiver systems.
Software for each receiver evaluates the first character of each message. The
receiver is placed in wakeup mode by writing a 1 to the RWU bit in the SCCR2
register. While RWU is 1, all of the receiver-related status flags (RDRF, IDLE, OR,
NF, and FE) are inhibited (cannot become set). Although RWU can be cleared by
a software write to SCCR2, to do so would be unusual. Normally, RWU is set by
software and is cleared automatically with hardware. Whenever a new message
begins, logic alerts the sleeping receivers to wake up and evaluate the initial
character of the new message.
Two methods of wakeup are available:
Idle line wakeup
Address mark wakeup
During idle line wakeup, a sleeping receiver awakens as soon as the RxD line
becomes idle. In the address mark wakeup, logic 1 in the most significant bit (MSB)
of a character wakes up all sleeping receivers.
6.5.1 Idle-Line Wakeup
To use the receiver wakeup method, establish a software addressing scheme to
allow the transmitting devices to direct a message to individual receivers or to
groups of receivers. This addressing scheme can take any form as long as all
transmitting and receiving devices are programmed to understand the same
scheme. Because the addressing information is usually the first frame(s) in a
message, receivers that are not part of the current task do not become burdened
with the entire set of addressing frames. All receivers are awake (RWU = 0) when
each message begins. As soon as a receiver determines that the message is not
intended for it, software sets the RWU bit (RWU = 1), which inhibits further flag
setting until the RxD line goes idle at the end of the message. As soon as an idle
line is detected by receiver logic, hardware automatically clears the RWU bit so that
the first frame of the next message can be received. This type of receiver wakeup
requires a minimum of one idle-line frame time between messages and no idle time
between frames in a message.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
发布紧急采购，3分钟左右您将得到回复。