- 您现在的位置：买卖IC网 > PDF目录69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF资料下载
参数资料
| 型号： | MCC68HC711D3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封装： | DIE |
| 文件页数： | 149/157页 |
| 文件大小： | 2252K |
| 代理商： | MCC68HC711D3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页当前第149页第150页第151页第152页第153页第154页第155页第156页第157页
Serial Peripheral Interface (SPI)
SPI System Errors
MC68HC711D3 — Rev. 2
Data Sheet
MOTOROLA
Serial Peripheral Interface (SPI)
91
The state of the master and slave CPHA bits affects the operation of SS. CPHA
settings should be identical for master and slave. When CPHA = 0, the shift clock
is the OR of SS with SCK. In this clock phase mode, SS must go high between
successive characters in an SPI message. When CPHA = 1, SS can be left low
between successive SPI characters. In cases where there is only one SPI slave
MCU, its SS line can be tied to VSS as long as only CPHA = 1 clock mode is used.
7.6 SPI System Errors
Two system errors can be detected by the SPI system. The first type of error arises
in a multiple-master system when more than one SPI device simultaneously tries
to be a master. This error is called a mode fault. The second type of error, write
collision, indicates that an attempt was made to write data to the SPDR while a
transfer was in progress.
When the SPI system is configured as a master and the SS input line goes to active
low, a mode fault error has occurred — usually because two devices have
attempted to act as master at the same time. In cases where more than one device
is concurrently configured as a master, there is a chance of contention between
two pin drivers. For push-pull CMOS drivers, this contention can cause permanent
damage. The mode fault attempts to protect the device by disabling the drivers.
The MSTR control bit in the SPCR and all four DDRD control bits associated with
the SPI are cleared. An interrupt is generated subject to masking by the SPIE
control bit and the I bit in the CCR.
Other precautions may need to be taken to prevent driver damage. If two devices
are made masters at the same time, mode fault does not help protect either one
unless one of them selects the other as slave. The amount of damage possible
depends on the length of time both devices attempt to act as master.
A write collision error occurs if the SPDR is written while a transfer is in progress.
Because the SPDR is not double buffered in the transmit direction, writes to SPDR
cause data to be written directly into the SPI shift register. Because this write
corrupts any transfer in progress, a write collision error is generated. The transfer
continues undisturbed, and the write data that caused the error is not written to the
shifter.
A write collision is normally a slave error because a slave has no control over when
a master initiates a transfer. A master knows when a transfer is in progress, so
there is no reason for a master to generate a write-collision error, although the SPI
logic can detect write collisions in both master and slave devices.
The SPI configuration determines the characteristics of a transfer in progress. For
a master, a transfer begins when data is written to SPDR and ends when SPIF is
set. For a slave with CPHA equal to zero, a transfer starts when SS goes low and
ends when SS returns high. In this case, SPIF is set at the middle of the eighth SCK
cycle when data is transferred from the shifter to the parallel data register, but the
transfer is still in progress until SS goes high. For a slave with CPHA equal to one,
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
发布紧急采购，3分钟左右您将得到回复。