- 您现在的位置：买卖IC网 > PDF目录69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF资料下载
参数资料
| 型号： | MCC68HC711D3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封装： | DIE |
| 文件页数： | 157/157页 |
| 文件大小： | 2252K |
| 代理商： | MCC68HC711D3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页当前第157页
Programmable Timer
Input Capture
MC68HC711D3 — Rev. 2
Data Sheet
MOTOROLA
Programmable Timer
99
of successive edges of an incoming signal, software can determine the period and
pulse width of a signal. To measure period, two successive edges of the same
polarity are captured. To measure pulse width, two alternate polarity edges are
captured.
In most cases, input capture edges are asynchronous to the internal timer counter,
which is clocked relative to the PH2 clock. These asynchronous capture requests
are synchronized to PH2 so that the latching occurs on the opposite half cycle of
PH2 from when the timer counter is being incremented. This synchronization
process introduces a delay from when the edge occurs to when the counter value
is detected. Because these delays offset each other when the time between two
edges is being measured, the delay can be ignored. When an input capture is
being used with an output compare, there is a similar delay between the actual
compare point and when the output pin changes state.
The control and status bits that implement the input capture functions are
contained in the PACTL, TCTL2, TMSK1, and TFLG1 registers.
To configure port A bit 3 as an input capture, clear the DDRA3 bit of the PACTL
register. Note that this bit is cleared out of reset. To enable PA3 as the fourth input
capture, set the I4/O5 bit in the PACTL register. Otherwise, PA3 is configured as a
fifth output compare out of reset, with bit I4/O5 being cleared. If the DDRA3 bit is
set (configuring PA3 as an output), and IC4 is enabled, then writes to PA3 cause
edges on the pin to result in input captures. Writing to TI4/O5 has no effect when
the TI4/O5 register is acting as IC4.
8.3.1 Timer Control 2 Register
Use the control bits of timer control 2 register (TCTL2) to program input capture
functions to detect a particular edge polarity on the corresponding timer input pin.
Each of the input capture functions can be independently configured to detect
rising edges only, falling edges only, any edge (rising or falling), or to disable the
input capture function. The input capture functions operate independently of each
other and can capture the same TCNT value if the input edges are detected within
the same timer count cycle.
EDGxB and EDGxA — Input Capture Edge Control
There are four pairs of these bits. Each pair is cleared to 0 by reset and must be
encoded to configure the corresponding input capture edge detector circuit. IC4
Address:
$0021
Bit 7
654321
Bit 0
Read:
EDG4B
EDG4A
EDG1B
EDG1A
EDG2B
EDG2A
EDG3B
EDG3A
Write:
Reset:
00000000
Figure 8-3. Timer Control 2 Register (TCTL2)
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
发布紧急采购，3分钟左右您将得到回复。