- 您现在的位置：买卖IC网 > PDF目录12015 > ADUC834BSZ (Analog Devices Inc)IC ADC DUAL16/24BIT W/MCU 52MQFP PDF资料下载
参数资料
| 型号： | ADUC834BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/80页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL16/24BIT W/MCU 52MQFP |
| 产品培训模块： | Process Control |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
REV. A
–18–
ADuC834
ADCMODE (ADC Mode Register)
Used to control the operational mode of both ADCs.
SFR Address
D1H
Power-On Default Value
00H
Bit Addressable
No
Table V. ADCMODE SFR Bit Designations
Bit
Name
Description
7
–––
Reserved for Future Use
6
–––
Reserved for Future Use
5
ADC0EN
Primary ADC Enable.
Set by the user to enable the primary ADC and place it in the mode selected in MD2–MD0 below.
Cleared by the user to place the primary ADC in power-down mode.
4
ADC1EN
Auxiliary ADC Enable.
Set by the user to enable the auxiliary ADC and place it in the mode selected in MD2–MD0 below.
Cleared by the user to place the auxiliary ADC in power-down mode.
3
–––
Reserved for Future Use
2
MD2
Primary and auxiliary ADC Mode bits.
1
MD1
These bits select the operational mode of the enabled ADC as follows:
0
MD0
MD2 MD1 MD0
0
00
ADC Power-Down Mode (Power-On Default)
0
01
Idle Mode. In Idle Mode, the ADC filter and modulator are held in a reset state
although the modulator clocks are still provided.
0
10
Single Conversion Mode. In Single Conversion Mode, a single conversion is
performed on the enabled ADC. On completion of the conversion, the ADC data
registers (ADC0H/M/L and/or ADC1H/L) are updated, the relevant flags in the
ADCSTAT SFR are written, and power-down is re-entered with the MD2–MD0
accordingly being written to 000.
0
11
Continuous Conversion. In Continuous Conversion Mode, the ADC data registers
are regularly updated at the selected update rate (see SF Register).
1
00
Internal Zero-Scale Calibration. Internal short automatically connected to the
enabled ADC input(s).
1
01
Internal Full-Scale Calibration Internal or External VREF (as determined by
XREF0 and XREF1 bits in ADC0/1CON) is automatically connected to the
enabled ADC input(s) for this calibration.
1
10
System Zero-Scale Calibration. User should connect system zero-scale input to
the enabled ADC input(s) as selected by CH1/CH0 and ACH1/ACH0 bits in
the ADC0/1CON Register.
1
11
System Full-Scale Calibration. User should connect system full-scale input to
the enabled ADC input(s) as selected by CH1/CH0 and ACH1/ACH0 bits in the
ADC0/1CON Register.
NOTES
1. Any change to the MD bits will immediately reset both ADCs. A write to the MD2–0 Bits with no change is also treated as a reset. (See exception to this in Note 3 below.)
2. If ADC0CON is written when ADC0EN = 1, or if ADC0EN is changed from 0 to 1, then both ADCs are also immediately reset. In other words, the primary ADC
is given priority over the auxiliary ADC and any change requested on the primary ADC is immediately responded to.
3. On the other hand, if ADC1CON is written or if ADC1EN is changed from 0 to 1, only the auxiliary ADC is reset. For example, if the primary ADC is continuously
converting when the auxiliary ADC change or enable occurs, the primary ADC continues undisturbed. Rather than allow the auxiliary ADC to operate with a phase
difference from the primary ADC, the auxiliary ADC will fall into step with the outputs of the primary ADC. The result is that the first conversion time for the
auxiliary ADC will be delayed up to three outputs while the auxiliary ADC update rate is synchronized to the primary ADC.
4. Once ADCMODE has been written with a calibration mode, the RDY0/1 bits (ADCSTAT) are immediately reset and the calibration commences. On completion,
the appropriate calibration registers are written, the relevant bits in ADCSTAT are written, and the MD2–0 bits are reset to 000 to indicate the ADC is back in
power-down mode.
5. Any calibration request of the auxiliary ADC while the temperature sensor is selected will fail to complete. Although the RDY1 bit will be set at the end of the
calibration cycle, no update of the calibration SFRs will take place and the ERR1 bit will be set.
6. Calibrations are performed at maximum SF (see SF SFR) value guaranteeing optimum calibration operation.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVP-IY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-B3D-IY-F2 | CONVERTER MOD DC/DC 85V 50W |
| AT91SAM9XE256-QU | MCU ARM9 256K FLASH 208-PQFP |
| VI-JVN-IY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-JVM-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC836 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADUC836BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。