- 您现在的位置：买卖IC网 > PDF目录12015 > ADUC834BSZ (Analog Devices Inc)IC ADC DUAL16/24BIT W/MCU 52MQFP PDF资料下载
参数资料
| 型号： | ADUC834BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 64/80页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL16/24BIT W/MCU 52MQFP |
| 产品培训模块： | Process Control |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页当前第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
REV. A
ADuC834
–67–
OTHER HARDWARE CONSIDERATIONS
In-Circuit Serial Download Access
Nearly all ADuC834 designs will want to take advantage of the
in-circuit reprogrammability of the chip. This is accomplished
by a connection to the ADuC834’s UART, which requires an
external RS-232 chip for level translation if downloading code
from a PC. Basic configuration of an RS-232 connection is
illustrated in Figure 66 with a simple ADM3202-based circuit.
If users would rather not include an RS-232 chip onto the target
board, refer to the application note uC006–A 4-Wire UART-to-PC
Interface available at www.analog.com/microconverter, for a
simple (and zero-cost-per-board) method of gaining in-circuit
serial download access to the ADuC834.
In addition to the basic UART connections, users will also need
a way to trigger the chip into Download mode. This is accom-
plished via a 1 k
pull-down resistor that can be jumpered onto
the
PSEN pin, as shown in Figure 66. To get the ADuC834 into
Download mode, simply connect this jumper and power-cycle
the device (or manually reset the device, if a manual reset button
is available) and it will be ready to receive a new program serially.
With the jumper removed, the device will power-on in Normal
mode (and run the program) whenever power is cycled or RESET
is toggled.
Note that
PSEN is normally an output (as described in the
External Memory Interface section) and it is sampled as an input
only on the falling edge of RESET (i.e., at power-up or upon an
external manual reset). Note also that if any external circuitry
unintentionally pulls
PSEN low during power-up or reset events,
it could cause the chip to enter Download Mode and therefore
fail to begin user code execution as it should. To prevent this,
ensure that no external signals are capable of pulling the
PSEN
pin low, except for the external
PSEN jumper itself.
Embedded Serial Port Debugger
From a hardware perspective, entry to Serial Port Debug mode
is identical to the serial download entry sequence described
above. In fact, both Serial Download and Serial Port Debug
modes can be thought of as essentially one mode of operation
used in two different ways.
Note that the serial port debugger is fully contained on the
ADuC834 device, (unlike “ROM monitor” type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
Single-Pin Emulation Mode
Also built into the ADuC834 is a dedicated controller for single-
pin in-circuit emulation (ICE) using standard production ADuC834
devices. In this mode, emulation access is gained by connection
to a single pin, the
EA pin. Normally, this pin is hard-wired
either high or low to select execution from internal or external
program memory space, as described earlier. To enable single-pin
emulation mode, however, users will need to pull the
EA pin
high through a 1 k
resistor as shown in Figure 66. The emulator
will then connect to the 2-pin header also shown in Figure 66.
To be compatible with the standard connector that comes
with the single-pin emulator available from Accutron Limited
(www.accutron.com), use a 2-pin 0.1-inch pitch Friction Lock
header from Molex (www.molex.com) such as their part number
22-27-2021. Be sure to observe the polarity of this header. As
represented in Figure 66, when the Friction Lock tab is at the
right, the ground pin should be the lower of the two pins (when
viewed from the top).
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVP-IY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-B3D-IY-F2 | CONVERTER MOD DC/DC 85V 50W |
| AT91SAM9XE256-QU | MCU ARM9 256K FLASH 208-PQFP |
| VI-JVN-IY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-JVM-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC836 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADUC836BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。