- 您现在的位置：买卖IC网 > PDF目录12015 > ADUC834BSZ (Analog Devices Inc)IC ADC DUAL16/24BIT W/MCU 52MQFP PDF资料下载
参数资料
| 型号： | ADUC834BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 27/80页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL16/24BIT W/MCU 52MQFP |
| 产品培训模块： | Process Control |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
REV. A
ADuC834
–33–
Programming the Flash/EE Data Memory
A user wishes to program F3H into the second byte on Page 03H
of the Flash/EE data memory space while preserving the other
three bytes already in this page.
A typical program of the Flash/EE data array will involve:
1. setting EADRH/L with the page address
2. writing the data to be programmed to the EDATA1–4
3. writing the ECON SFR with the appropriate command
Step 1: Set Up the Page Address
The two address registers EADRH and EADRL hold the high
byte address and the low byte address of the page to be addressed.
The assembly language to set up the address may appear as:
MOV
EADRH,#0
;
Set Page Address Pointer
MOV
EADRL,#03H
Step 2: Set Up the EDATA Registers
The four values to be written into the page into the 4 SFRs
EDATA1–4. Unfortunately we do not know three of them. Thus it
is necessary to read the current page and overwrite the second byte.
MOV
ECON,#1
;
Read Page into EDATA1-4
MOV
EDATA2,#0F3H ;
Overwrite byte 2
Step 3: Program Page
A byte in the Flash/EE array can only be programmed if it has
previously been erased. To be more specific, a byte can only be
programmed if it already holds the value FFH. Because of the
Flash/EE architecture, this erase must happen at a page level.
Therefore, a minimum of 4 bytes (1 page) will be erased when
an erase command is initiated. Once the page is erased, we can
program the 4 bytes in-page and then perform a verification of
the data.
MOV ECON,#5
;
ERASE Page
MOV ECON,#2
;
WRITE Page
MOV ECON,#4
;
VERIFY Page
MOV A,ECON
;
Check if ECON=0 (OK!)
JNZ ERROR
Note: although the 4 Kbytes of Flash/EE data memory is shipped
from the factory pre-erased, i.e., Byte locations set to FFH, it is
nonetheless good programming practice to include an erase-all
routine as part of any configuration/setup code running on the
ADuC834. An “ERASE-ALL” command consists of writing
“06H” to the ECON SFR, which initiates an erase of the 4-Kbyte
Flash/EE array. This command coded in 8051 assembly would
appear as:
MOV ECON,#06H
;
Erase all Command
;
2 ms Duration
Flash/EE Memory Timing
Typical program and erase times for the ADuC834 are as follows:
Normal Mode (operating on Flash/EE data memory)
READPAGE (4 bytes)
– 5 machine cycles
WRITEPAGE (4 bytes)
– 380
s
VERIFYPAGE (4 bytes)
– 5 machine cycles
ERASEPAGE (4 bytes)
– 2 ms
ERASEALL (4 Kbytes)
– 2 ms
READBYTE (1 byte)
– 3 machine cycles
WRITEBYTE (1 byte)
– 200
s
ULOAD Mode (operating on Flash/EE program memory)
WRITEPAGE (256 bytes)
– 15 ms
ERASEPAGE (64 bytes)
– 2 ms
ERASEALL (56 Kbytes)
– 2 ms
WRITEBYTE (1 byte)
– 200
s
It should be noted that a given mode of operation is initiated as
soon as the command word is written to the ECON SFR. The
core microcontroller operation on the ADuC834 is idled until
the requested Program/Read or Erase mode is completed.
In practice, this means that even though the Flash/EE memory
mode of operation is typically initiated with a two-machine cycle
MOV instruction (to write to the ECON SFR), the next instruction
will not be executed until the Flash/EE operation is complete.
This means that the core will not respond to interrupt requests
until the Flash/EE operation is complete, although the core
peripheral functions like Counter/Timers will continue to count
and time as configured throughout this period.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVP-IY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-B3D-IY-F2 | CONVERTER MOD DC/DC 85V 50W |
| AT91SAM9XE256-QU | MCU ARM9 256K FLASH 208-PQFP |
| VI-JVN-IY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-JVM-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC836 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADUC836BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。