- 您现在的位置：买卖IC网 > PDF目录166397 > B900J24PXX12I 0-BIT, 80 MHz, OTHER DSP, PQFP44 PDF资料下载
参数资料
| 型号： | B900J24PXX12I |
| 元件分类： | 数字信号处理 |
| 英文描述： | 0-BIT, 80 MHz, OTHER DSP, PQFP44 |
| 文件页数： | 92/100页 |
| 文件大小： | 1547K |
| 代理商： | B900J24PXX12I |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页当前第92页第93页第94页第95页第96页第97页第98页第99页第100页
Lucent Technologies Inc.
91
Advance Data Sheet
B900
July 1999
Baseband Signal Processor
9 Crystal Oscillator Electrical
Requirements and Characteristics
This section describes electrical requirements and
characteristics for high- and low-frequency crystal
oscillator circuits.
9.1
Crystal Oscillator
If the option for using the external crystal is chosen, the
electrical requirements and characteristics described
in this section apply.
9.1.1 Crystal Oscillator Power Dissipation
The typical power dissipation at 4.096 MHz of the inter-
nal high-frequency crystal oscillator circuit below is
6 mW at 5 V and 4 mW at 3 V.
9.1.2 Crystal Oscillator External Components
The crystal oscillator is enabled by connecting a crystal
across XTALA and XTALB, along with one external
capacitor from each of these pins to ground (see Fig-
ure 24). For most applications, 15 pF external capaci-
tors are recommended; however, larger values may be
necessary if precise frequency tolerance is required
ations). The crystal should be either fundamental or
overtone mode, parallel resonant, with a power dissi-
pation of at least 1 mW, and be specified at a load
capacitance equal to the total capacitance seen by the
crystal (including external capacitors and strays).
The series resistance of the crystal should be specified
to be less than half the absolute value of the negative
frequency.
5-4041
Figure 24. Fundamental Crystal Configuration
The following guidelines should be followed when
designing the printed-circuit board layout for a crystal-
based application:
s
Keep crystal and external capacitors as close to
XTALA and XTALB pins as possible to minimize
board stray capacitance.
s
Keep high-frequency digital signals such as DOUT
away from XTALA and XTALB traces to avoid
coupling.
CRYSTAL
XTAL1OUT
XTAL1IN
C 1
C 2
Re(Z)
CO
相关PDF资料 |
PDF描述 |
|---|---|
| B900J24FXX12IT | 0-BIT, 59.88 MHz, OTHER DSP, PQFP44 |
| BA00CC0WCP-V5 | 1A Low Dropout Voltage Regulator with Shut Down Switch(Adustable Voltage) |
| BA10E6 | COPPER ALLOY, TIN FINISH, RING TERMINAL |
| BA12004 | 0.5 A, 7 CHANNEL, NPN, Si, POWER TRANSISTOR |
| BA1518SUR5VP | SINGLE COLOR DISPLAY CLUSTER, ULTRA RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B-900-M-10 | 制造商:Thomas & Betts 功能描述: |
| B-900-M-10-EG | 制造商:Thomas & Betts 功能描述: |
| B-900-M-20 | 制造商:Thomas & Betts 功能描述: |
| B-900-M-20-EG | 制造商:Thomas & Betts 功能描述: |
| B901 | 制造商:EDAL 制造商全称:EDAL 功能描述:Silicon Bridge Rectifier |
发布紧急采购，3分钟左右您将得到回复。