- 您现在的位置：买卖IC网 > PDF目录18822 > HSP50214BVCZ (Intersil)IC DOWNCONVERTER 14BIT 120-MQFP PDF资料下载
参数资料
| 型号： | HSP50214BVCZ |
| 厂商： | Intersil |
| 文件页数： | 25/62页 |
| 文件大小： | 0K |
| 描述： | IC DOWNCONVERTER 14BIT 120-MQFP |
| 标准包装： | 24 |
| 功能： | 降频器 |
| RF 型： | AMPS，CDMA，GSM，TDMA |
| 封装/外壳： | 120-BQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
HSP50214B
N = [ ( f PROCCLK /f OUT ) – 1 ]
These gain error values are scaled by the programmable
AGC loop gains to adjust the data path gain.
The maximum slew rate is ~1.5dB per output sample. See
Equation 18.
In order to fully evaluate the dynamic range of the PDC,
Table 9B is provided, which details the bit weighting from the
input to the AGC Multiplier.
Re-Sampler/Halfband Filter
The re-sampler is an NCO controlled polyphase filter that
allows the output sample rate to have a non-integer
relationship to the input sample rate. The filter engine can be
viewed conceptually as a fixed interpolation filter, followed by
an NCO controlled decimator.
The prototype polyphase filter has 192 taps designed at 32
times the input sample rate. Each of the 32 phases has 6
filter taps (6)(32) = 192. The stopband attenuation of the
prototype filter is greater than 60dB, as shown in Figure 24.
The signal to total image power ratio is approximately 55dB,
due to the aliasing of the interpolation images. The filter is
capable of decimation factors from 1 to 4. If the output is at
least 2x the baud rate, the 32 interpolation phases yield an
effective sample rate of 64x the baud rate or approximately
1.5%, (1/64), maximum timing error.
Following the Re-sampler are two interpolation halfband
filters. The halfband filters allow the user to up-sample by 2
or 4 to recover time resolution lost by decimating.
Interpolating by 2 or 4 gives 1/4 or 1/8 baud time resolution
(assuming 2x baud at the re-sampler output). The halfband
filters use the same coefficients as HB3 and HB5 from the
Halfband Filters Section. If one halfband is used, the 23-tap
filter is chosen. If two are used, the 23-tap filter runs first
0
-20
-40
-60
-80
-100
followed by the 15-tap filter operating at twice the first
halfband’s rate. The 23-tap filter requires 7 multiplies, and
the 15-tap filter requires 5 multiplies to complete a filter
calculation.
Using the interpolation halfband filters allows for reduction in
the FIR filter sample rate. This optimizes the use of the
programmable FIR filter by allowing the FIR output sample
rate to be closer to the Nyquist rate of the desired bandwidth.
Optimizing the FIR filter performance provides better use of
the programmable FIR taps. Table 10 details the maximum
clocking rates for the possible resampling and interpolation
halfband filter configurations of this section of the PDC.
Control Word 16, Bits 2-0 identify the filter configuration.
Control Word 16, Bit 3 is used to bypass the polyphase re-
sampler filter.
For proper data output from the interpolation filters, the data
ready signal must account for the interpolation process.
Figure 25 illustrates the insertion of additional data ready
pulses to provide sufficient pulses for the new output sample
rate. The Re-sampler Output Pulse Delay parameter is set in
Control Word 16, Bits 4-11. These bits set the delay between
the output samples when interpolation is utilized. Program
this distance between pulses using
(EQ. 20)
A value of at least 5 is required to have sufficient time to
update the Output Buffer Register. (Writing 5 samples
requires 5 clock cycles) A value of at least 16 is required for
proper serial output from the part. (Conversion from 16-bit
parallel to serial). The value is programmed in numbers of
PROCCLK’s.
10
0
-10
-20
-30
-40
-50
-60
-70
-120
1
2
3
4 5 6 7 8 9 10 11 12 13 14 15 16
FREQUENCY (RELATIVE TO f S )
-80
0
FREQUENCY (RELATIVE TO f S )
FIGURE 24A. POLYPHASE RESAMPLER FILTER BROADBAND
FREQUENCY RESPONSE
FIGURE 24B. POLYPHASE RESAMPLER FILTER PASS BAND
FREQUENCY RESPONSE
There is a 65dB limitation in SNR using the Re-Sampler Filter. When only the Interpolation FIRs are used, the full SNR range is passed.
FIGURE 24.
25
FN4450.4
May 1, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HMR2300-D21-232 | MAGNETOMETER RS232 W/CASE |
| V-16-4A5 | SWITCH MINI SPDT 16A PIN PLUNGER |
| HMR2300-D20-232 | MAGNETOMETER RS232 W/CASE |
| D2MV-1L-1C2 | BASIC SWITCH |
| HMR2300-D00-232 | MAGNETOMETER RS232 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HSP50214BVI | 功能描述:上下转换器 120L MQFP INDTEMP 14-BIT PROGRAMMABLE DOWNCONVERTER 65MSPS RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50214BVIZ | 功能描述:上下转换器 120L MQFP INDTEMP 14-BIT PROG DWNCNVRT RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50214VC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HSP50214VI | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HSP50215 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:DSP Modulator Evaluation Board |
发布紧急采购，3分钟左右您将得到回复。