- 您现在的位置：买卖IC网 > PDF目录18822 > HSP50214BVCZ (Intersil)IC DOWNCONVERTER 14BIT 120-MQFP PDF资料下载
参数资料
| 型号： | HSP50214BVCZ |
| 厂商： | Intersil |
| 文件页数： | 47/62页 |
| 文件大小： | 0K |
| 描述： | IC DOWNCONVERTER 14BIT 120-MQFP |
| 标准包装： | 24 |
| 功能： | 降频器 |
| RF 型： | AMPS，CDMA，GSM，TDMA |
| 封装/外壳： | 120-BQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
HSP50214B
Configuration Control Word Definitions
Note that in the Configuration Control Register Tables, some
of the available 32-bits in a Control Word are not used.
Unused bits do not need to be written to the Master Register.
If the destination only has 16-bits, then only 2 bytes need to
be written to the Master Register. Figure 45 details the timing
for proper operation of the Microprocessor Write Section. Bits
identified as “Reserved” should be programmed to a zero.
NOTE: CLKIN or PROCCLK must be present to properly load
control words. Note in the header which is applicable.
CONTROL WORD 0: CHIP CONFIGURATION, INPUT SECTION, CIC GAIN (SYNCHRONOUS TO CLKIN)
BIT
POSITION
31-21
20
19
18
17
16-13
12-7
6
5-4
3
2
1
0
FUNCTION
Reserved
Carrier NCO External
Sync Enable
CIC External Sync
Enable
Input Format
Input Mode
CIC Shift Gain
CIC Decimation
Counter Preload
CIC Bypassed
Number of Offset
Frequency Bits
Syncout CLK Select
Clear Phase Accum
Carrier NCO Offset
Frequency Enable
Carrier NCO Load
Phase Accum On
Update
47
DESCRIPTION
Reserved.
0- The SYNCIN1 pin has no effect on the Carrier NCO.
1- When the SYNCIN1 pin is asserted, the carrier center frequency and phase are updated from the
holding registers to the active register. Also, if bit 0 of this word is active, the carrier phase accumulator
feedback will be zeroed to set the Carrier NCO to a known phase, allowing the NCOs of multiple parts
to be initialized and updated synchronously.
0- The SYNCIN1 pin has no effect on the CIC filter.
1- When the SYNCIN1 pin is asserted, the decimation counter is loaded, allowing the decimation
counters in multiple chips to be synchronized. When CW27 bit-22 is set to a 1, SYNCIN1 will reset both
front end and back end circuitry.
0- Two’s Complement Input Format.
1- Offset Binary Input Format.
0- Input operates in Gated Mode.
1- Input operates in Interpolated Mode.
These bits control the barrel shifter at the input to the CIC filter. These bits are added to the
GAINADJ(2:0) pins to determine the total shift. The sum is saturated at 15. See the CIC Decimation Filter
Section for values to be programmed in this field based on CIC filter Decimation. Bit 16 is the MSB.
SG = Floor [39 - (number of input bits) - 5log 2 (R)] for 4 < R < 31
SG = 15 for R = 4.
SG = 0 for R = 32.
These bits control the decimation in the CIC filter. Program this field to R-1, where R is the desired
decimation factor in the filter. The decimation factor range is 4-32. See CIC Filter Section for effective
decimation range relative to the CIC Shift Gain value. Bit 12 is the MSB.
While this field allows values from 0 - 63, the valid values are in the range from 4- 32.
Active high, this bit routes the output of the input shifter to the output of the CIC with no filtering.
When the CIC filter is bypassed, CLKIN must be at least twice the input sample rate (ENI should be
toggled to achieve this). When the CIC filter is bypassed, the bottom 24-bits of the barrel shifter output
are routed to the halfband filters.
00 - 8-bits.
01 - 16.
10 - 24.
11 - 32.
This bit selects whether the SYNCOUT signal is generated from CLKIN of from PROCCLK
0- CLKIN.
1- PROCLK.
0- Enable accumulator in Carrier NCO.
1- Zero feedback in accumulator.
When set to 1, this bit enables the offset frequency word to be added to the center frequency Control
Word. The offset is loaded serially via the COF and COFSYNC pins.
When this bit is set to 1, the μ P update to the Carrier NCO frequency or an external carrier NCO load
using SYNCIN1 will zero the feedback of the phase accumulator, as well as update the phase or
frequency. This function can be used to set the NCO to a known phase synchronized to an external
event.
FN4450.4
May 1, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HMR2300-D21-232 | MAGNETOMETER RS232 W/CASE |
| V-16-4A5 | SWITCH MINI SPDT 16A PIN PLUNGER |
| HMR2300-D20-232 | MAGNETOMETER RS232 W/CASE |
| D2MV-1L-1C2 | BASIC SWITCH |
| HMR2300-D00-232 | MAGNETOMETER RS232 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HSP50214BVI | 功能描述:上下转换器 120L MQFP INDTEMP 14-BIT PROGRAMMABLE DOWNCONVERTER 65MSPS RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50214BVIZ | 功能描述:上下转换器 120L MQFP INDTEMP 14-BIT PROG DWNCNVRT RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50214VC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HSP50214VI | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HSP50215 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:DSP Modulator Evaluation Board |
发布紧急采购，3分钟左右您将得到回复。