- 您现在的位置：买卖IC网 > PDF目录1924 > IDT82P2828BHG (IDT, Integrated Device Technology Inc)IC LIU T1/J1/E1 28+1CH 640-PBGA PDF资料下载
参数资料
| 型号： | IDT82P2828BHG |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 88/154页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1/E1 28+1CH 640-PBGA |
| 标准包装： | 5 |
| 类型： | 线路接口装置（LIU） |
| 规程： | E1 |
| 电源电压： | 3.13 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 640-BGA 裸露焊盘 |
| 供应商设备封装： | 640-PBGA-EP（31x31） |
| 包装： | 托盘 |
| 其它名称： | 82P2828BHG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页当前第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页
IDT82P2828
28(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Functional Description
39
February 6, 2009
3.3.5
LINE DRIVER
The Line Driver can be set to High-Z for protection or in redundant
applications.
The following two ways will set the Line Driver to High-Z:
Setting the OE pin to low will globally set all the Line Drivers to
High-Z;
Setting the OE bit (b6, TCF0,...) to ‘0’ will set the corresponding
Line Driver to High-Z.
By these ways, the functionality of the internal circuit is not affected
and TTIPn and TRINGn will enter High-Z state immediately.
3.3.5.1 Transmit Over Current Protection
The Line Driver monitors the Transmit Over Current (TOC) on the
line interface. When TOC is detected, the driver’s output (i.e., output on
TTIPn/TRINGn) is determined by the THZ_OC bit (b4, TCF0,...). If the
THZ_OC bit (b4, TCF0,...) is ‘0’, the driver’s output current (peak to
peak) is limited to 100 mA; if the THZ_OC bit (b4, TCF0,...) is ‘1’, the
driver’s output will enter High-Z. TOC is indicated by the TOC_S bit (b4,
STAT0,...). A transition from ‘0’ to ‘1’ on the TOC_S bit (b4, STAT0,...) or
any transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the TOC_S bit (b4,
STAT0,...) will set the TOC_IS bit (b4, INTS0,...) to ‘1’, as selected by the
TOC_IES bit (b4, INTES,...). When the TOC_IS bit (b4, INTS0,...) is ‘1’,
an interrupt will be reported by INT if not masked by the TOC_IM bit (b4,
TOC may be indicated by the TMFn pin. Refer to Section 3.5.7.2
TMFn Indication for details.
3.3.6
TX TERMINATION
The transmit line interface supports Transmit Differential mode and
Transmit Single Ended mode, as selected by the T_SING bit (b3,
TCF0,...). In Transmit Differential mode, both TTIPn and TRINGn are
used to transmit signals to the line side. In Transmit Single Ended mode,
only TTIPn is used to transmit signal.
The line interface can be connected with T1 100
, J1 110 or E1
120
twisted pair cable or E1 75 coaxial cable.
The transmit impedance matching is realized by using internal
impedance matching or external impedance matching for each channel
in different applications.
3.3.6.1 Transmit Differential Mode
In Transmit Differential mode, different applications have different
impedance matching. For T1/J1 applications, only Internal Impedance
Matching is supported. For E1 applications, both Internal and External
Impedance Matching are supported.
Internal Impedance Matching circuit uses an internal programmable
resistor (IM) only.
External Impedance Matching circuit uses an external resistor (Rt)
only.
A twisted pair cable can be connected with a 1:2 (step up) trans-
former or without a transformer (transformer-less), while a coaxial cable
must be connected with a 1:2 transformer.
The T_TERM[2:0] bits (b2~0, TCF0,...) should be set according to
different cable conditions, whether a transformer is used, and what kind
of Impedance Matching is selected.
Table-15 lists the recommended impedance matching value in
one channel in different applications.
The transformer-less connection will offer a termination option with
reduced cost and board space. However, the waveform amplitude is not
standard compliant, and surge protection and common mode depres-
sion should be enhanced depending on equipment environment..
Table-15 Impedance Matching Value in Transmit Differential Mode
Cable Condition
Internal Impedance Matching
External Impedance Matching
T_TERM[2:0]
Rt
T_TERM[2:0]
Rt
T1 100
twisted pair (with transformer)
000
0
(not supported)
J1 110
twisted pair (with transformer)
001
E1 120
twisted pair (with transformer), PULS[3:0]=0001
010
111
10
E1 75
coaxial (with transformer), PULS[3:0]=0000
011
T1 100
twisted pair (transformer-less)
100
(not supported)
J1 110
twisted pair (transformer-less)
101
E1 120
twisted pair (transformer-less), PULS[3:0]=0001
110
相关PDF资料 |
PDF描述 |
|---|---|
| IDT82P2916BFG | IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P5088BBG | IC LIU T1/E1/J1 OCTAL 256PBGA |
| IDT82V2041EPPG | IC LIU T1/J1/E1 1CH 44-TQFP |
| IDT82V2042EPFG | IC LIU T1/J1/E1 2CH SHORT 80TQFP |
| IDT82V2044EPFG | IC LIU T1/E1 QUAD SHORT 128-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT82P2916 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:16-Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2916BFG | 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA RoHS:是 类别:集成电路 (IC) >> 接口 - 电信 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 06/Feb/2012 标准包装:750 系列:* |
| IDT82P2916BFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P5088 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:Universal Octal T1/E1/J1 LIU with Integrated Clock Adapter |
| IDT82P5088BBBLANK | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:Universal Octal T1/E1/J1 LIU with Integrated Clock Adapter |
发布紧急采购，3分钟左右您将得到回复。