参数资料
型号: MC13892JVLR2
厂商: Freescale Semiconductor
文件页数: 118/158页
文件大小: 0K
描述: IC PMU I.MX51/37/35/27 186MAPBGA
标准包装: 1,000
应用: 电池管理,显示器(LED 驱动器),手持/移动设备,电源
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 186-LFBGA
供应商设备封装: 186-PBGA(12x12)
包装: 带卷 (TR)
FUNCTIONAL DEVICE OPERATION
LIGHTING SYSTEM
Table 110. Signaling LED Driver Characteristics
Parameter
Absolute Accuracy
Matching
Leakage
Condition
At 400 mV, 21 mA
LEDxDC[5:0] = 000000
Min
Typ
Max
15
10
1.0
Units
%
%
μ A
Apart from using the signal LED drivers for driving LEDs they can also be used as general purpose open drain outputs for logic
signaling or as generic PWM generator outputs. For the maximum voltage ratings.
the enable for the boost regulator is an OR of the following SPI bits (SWBSTEN, USBSWBSTEN, and LEDSWBSTEN). For
more details on the boost regulator and its control, see Supplies .
As with the backlight driver channels, the signaling LED drivers include ramp up and ramp down patterns are implemented in
hardware. Ramp patterns for each of the drivers is accessed with the corresponding LEDxRAMP bit.
The ramp itself is generated by increasing or decreasing the PWM duty cycle with a 1/32 step every 1/64 seconds. The ramp
time is therefore a function of the initial set PWM cycle and the final PWM cycle. As an example, starting from 0/32 and going to
32/32 will take 500 ms while going to from 8/32 to 16/32 takes 125 ms.
Note that the ramp function is executed upon every change in PWM cycle setting. If a PWM change is programmed via SPI
when LEDxRAMP = 0, then the change is immediate rather than spread out over a PWM sweep.
For color mixing and in order to guarantee a constant color, the color mixing should be obtained by the current level setting so
that the intensity is set through the PWM duty cycle.
In addition, programmable blink rates are provided. Blinking is obtained by lowering the PWM repetition rate of each of the
drivers through LEDxPER[1:0], while the on period is determined by the duty cycle setting. To avoid high frequency spur coupling
in the application, the switching edges of the output drivers are softened. During blinking, so LEDxPER[1:0] is not “00”, ramping
and dimming patterns cannot be applied.
MC13892
Analog Integrated Circuit Device Data
118
Freescale Semiconductor
相关PDF资料
PDF描述
ECM15DTAS CONN EDGECARD 30POS R/A .156 SLD
GBM25DRTN-S13 CONN EDGECARD 50POS .156 EXTEND
AK670M-5-R CABLE MINI USB 4PIN 5M 1.1 VERS
EEM28DSXI CONN EDGECARD 56POS DIP .156 SLD
MC13892JVKR2 IC PMU I.MX51/37/35/27 139MAPBGA
相关代理商/技术参数
参数描述
MC13892VK 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VKR2 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VL 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VLR2 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC1-38RX 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL