- 您现在的位置：买卖IC网 > PDF目录16590 > MC13892JVLR2 (Freescale Semiconductor)IC PMU I.MX51/37/35/27 186MAPBGA PDF资料下载
参数资料
| 型号： | MC13892JVLR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 93/158页 |
| 文件大小： | 0K |
| 描述： | IC PMU I.MX51/37/35/27 186MAPBGA |
| 标准包装： | 1,000 |
| 应用： | 电池管理，显示器（LED 驱动器），手持/移动设备，电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 186-LFBGA |
| 供应商设备封装： | 186-PBGA（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
BATTERY INTERFACE AND CONTROL
POWER DISSIPATION
Since the charge path operates in a linear fashion, the dissipation can be significant and care must be taken to ensure that
the external pass FETs M1 and M2 are not over dissipating when charging. By default, the charge system will protect against
this by a built-in power limitation circuit. This circuit will monitor the voltage drop between CHRGRAW and CHRGISNS, and the
current through the external sense resistor connected between CHRGISNS and BPSNS. When required,.a duty cycle is applied
to the M1 and M2 drivers and thus the charge current, in order to stay within the power budget. At the same time M3 is forced to
conduct to keep the application powered. In case of excessive supply conditions, the power limiter minimum duty cycle may not
be sufficiently small to maintain the actual power dissipation within budget. In that case, the charge path will be disabled and the
CHGFAULTI interrupt generated with the CHGFAULTS[1:0] bits set to 01.
The power budget can be programmed by SPI through the PLIM[1:0] bits. The power dissipation limiter can be disabled by
setting the PLIMDIS bit. In this case, it is advised to use close software control to estimate the dissipated power in the external
pass FETs. The power limiter is automatically disabled in serial path factory mode and in reverse mode.
Since a charger attachment can be a Turn-on event when a product is initially in the Off state, any non-default settings that
are intended for PLIM[1:0] and PLIMDIS, should be programmed early in the configuration sequence, to ensure proper supply
conditions adapted to the application. To avoid any false detection during power up, the power limiter output is blanked at the
start of the charge cycle. As a safety precaution though, the power dissipation is monitored and the desired duty cycle is
estimated. When this estimated duty cycle falls below the power limiter minimum duty cycle, the charger circuit will be disabled.
Table 66. Charger Power Dissipation Limiter Control
PLIM[1:0]
00 (default)
01
10
11
Power Limit (mW)
600
800
1000
1200
Table 67. Charger Power Dissipation Limiter Characteristics
Parameter
Power Limiter Accuracy
Power Limiter Control Period
Power Limiter Blanking Period
Power Limiter Minimum Duty Cycle
Condition
Up to 2x the power set by PLIM[1:0]
Upon charging enabling
Min
–
–
–
–
Typ
–
500
1500
10
Max
15
–
–
–
Units
%
ms
ms
%
REVERSE SUPPLY MODE
The battery voltage can be applied to an external accessory via the charge path, by setting the RVRSMODE bit high. The
current through the accessory supply path is monitored via the charge path sense resistor R2, and can be read out via the ADC.
The accessory supply path is disabled and an interrupt CHGSHORTI is generated when the slow or fast threshold is crossed.
The reverse path is disabled when a current reversal occurs and an interrupt CHREVI is generated.
Table 68. Accessory Supply Main Characteristics
Parameter
Short-circuit Current Slow Threshold
Slow Threshold Debounce Time
Short-circuit Current Fast Threshold
Fast Threshold Debounce Time
Current Reversal Threshold
Condition
Current from Accessory
Min
500
–
–
–
–
Typ
–
1.0
–
100
CHGCURR
Max
–
–
1840
–
–
Units
mA
ms
mA
μ s
mA
INTERNAL TRICKLE CHARGE CURRENT SOURCE
An internal current source between BP and BATTISNS provides small currents to the battery in cases of trickle charging a
dead battery. As can be seen under the description of the standalone charging, this source is activated by the charger state
machine, and its current level is selected based on the battery voltage. The source can also be enabled in software controlled
charging mode by setting the TREN bit. This source cannot be used in single path configurations because in that case,
BATTISNS and BP are shorted on the board.
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
93
相关PDF资料 |
PDF描述 |
|---|---|
| ECM15DTAS | CONN EDGECARD 30POS R/A .156 SLD |
| GBM25DRTN-S13 | CONN EDGECARD 50POS .156 EXTEND |
| AK670M-5-R | CABLE MINI USB 4PIN 5M 1.1 VERS |
| EEM28DSXI | CONN EDGECARD 56POS DIP .156 SLD |
| MC13892JVKR2 | IC PMU I.MX51/37/35/27 139MAPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC13892VK | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VKR2 | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VL | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VLR2 | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC1-38RX | 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL |
发布紧急采购，3分钟左右您将得到回复。