收藏本站
参数资料
型号： MC13892JVLR2
厂商： Freescale Semiconductor
文件页数： 62/158页
文件大小： 0K
描述： IC PMU I.MX51/37/35/27 186MAPBGA
标准包装： 1,000
应用： 电池管理，显示器（LED 驱动器），手持/移动设备，电源
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 186-LFBGA
供应商设备封装： 186-PBGA（12x12）
包装： 带卷 (TR)
FUNCTIONAL DEVICE OPERATION
OPERATING MODES
Table 25. Timer Main Characteristics
Timer
Under-voltage Timer
Reset Timer
Watchdog Timer
Power Cut Timer
Duration
4.0 ms
40 ms
128 ms
Programmable 0 to 8 seconds in 31.25 ms steps
TIMING DIAGRAMS
A Turn On event timing diagram example shows in Figure 12 .
Figure 12. Power Up Timing Diagram
POWER UP
At power up, switchers and regulators are sequentially enabled in time slots of 2.0 ms steps to limit the inrush current after an
initial delay of 8.0 ms, in which the core circuitry gets enabled. To ensure a proper power up sequence, the outputs of the
switchers are discharged at the beginning of a Cold Start. For that reason, an 8.0 ms delay allows the outputs of the linear
regulators to be fully discharged as well through the built-in discharge path. Time slots which include multiple regulator startups
will be sub-sequenced for additional inrush balancing. The peak inrush current per event is limited. Any under-voltage detection
at BP is masked while the power up sequencer is running.
The Power Up mode Select pins (PUMS1 and 2) are used to configure the startup characteristics of the regulators. Supply
enabling and output level options are selected by hardwiring the PUMSx pins for the desired configuration. The state of the
PUMSx pins can be read out via the sense bits PUMSSxx[1:0]. Tying the PUMSx pins to ground corresponds to 00, open to 01,
VCOREDIG to 10, and VCORE to 11.
The recommended power up strategy for end products is to bring up as little of the system as possible at booting, essentially
sequestering just the bare essentials, to allow processor startup and software to run. With such a strategy, the startup transients
are controlled at lower levels, and the rest of the system power tree can be brought up by software. This allows optimization of
supply ordering where specific sequences may be required, as well as supply default values. Software code can load up all of
the required programmable options to avoid sneak paths, under/over-voltage issues, startup surges, etc., without any change in
hardware. For this reason, the Power Gate drivers are limited to activation by software rather than the sequencer, allowing the
core(s) to startup before any peripheral loading is introduced.
The power up defaults Table 26 shows the initial setup for the voltage level of the switchers and regulators, and whether they
get enabled.
MC13892
Analog Integrated Circuit Device Data
62
Freescale Semiconductor
相关PDF资料
PDF描述
ECM15DTAS CONN EDGECARD 30POS R/A .156 SLD
GBM25DRTN-S13 CONN EDGECARD 50POS .156 EXTEND
AK670M-5-R CABLE MINI USB 4PIN 5M 1.1 VERS
EEM28DSXI CONN EDGECARD 56POS DIP .156 SLD
MC13892JVKR2 IC PMU I.MX51/37/35/27 139MAPBGA
相关代理商/技术参数
参数描述
MC13892VK 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VKR2 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VL 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VLR2 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC1-38RX 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*