- 您现在的位置：买卖IC网 > PDF目录16590 > MC13892JVLR2 (Freescale Semiconductor)IC PMU I.MX51/37/35/27 186MAPBGA PDF资料下载
参数资料
| 型号： | MC13892JVLR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 57/158页 |
| 文件大小： | 0K |
| 描述： | IC PMU I.MX51/37/35/27 186MAPBGA |
| 标准包装： | 1,000 |
| 应用： | 电池管理，显示器（LED 驱动器），手持/移动设备，电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 186-LFBGA |
| 供应商设备封装： | 186-PBGA（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页当前第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
OPERATING MODES
POWER CONTROL MODES DESCRIPTION
Following are text descriptions of the power states of the system, which give additional details of the state machine, and
complement Figure 11 . Note that the SPI control is only possible in the Watchdog, On, and User Off Wait states, and that the
interrupt line INT is kept low in all states except for Watchdog and On.
Off
If the supply at BP is above the UVDET threshold, only the IC core circuitry at VCOREDIG and the RTC module are powered,
all other supplies are inactive. To exit the Off mode, a valid turn on event is required. No specific timer is running in this mode.
If the supply at BP is below the UVDET threshold no turn on events are accepted. If a valid coin cell is present, the core gets
powered from LICELL. The only active circuitry is the RTC module, with BP greater than UVDET detection, and the SRTC support
circuitry, if so configured.
Cold Start
Entered upon a Turn On event from Off, Warm Boot, successful PCUT, or Silent System Restart. The switchers and regulators
are powered up sequentially to limit the inrush current. See the Power Up section for sequencing and default level details. The
reset signals RESETB and RESETBMCU are kept low. The Reset timer starts running when entering a Cold Start. When expired,
the Cold Start state is exited for the Watchdog state, and both RESETB and RESETBMCU become high (open drain output with
external pull ups). The input control pins WDI, and STANDBYx are ignored.
Watchdog
The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The Watchdog timer starts running
when entering the Watchdog state. When expired, the system transitions to the On state, where WDI will be checked and
monitored. The input control pins WDI and STANDBYx are ignored while in the Watchdog state.
On
The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The WDI pin must be high to stay
in this mode. The WDI IO supply voltage is referenced to SPIVCC (Normally connected to SW4). SPIVCC must therefore remain
enabled to allow for proper WDI detection. If WDI goes low, the system will transition to the Off state or Cold Start (depending on
the configuration. Refer to the section on Silent System Restart with WDI Event for details).
User Off Wait
The system is fully powered and under SPI control. The WDI pin no longer has control over the part. The Wait mode is entered
by a processor request for User Off by setting the USEROFFSPI bit high. This is normally initiated by the end user via the power
key. Upon receiving the corresponding interrupt, the system will determine if the product has been configured for User Off or
Memory Hold states (both of which first require passing through User Off Wait) or just transition to Off.
The Wait timer starts running when entering User Off Wait mode. This leaves the processor time to suspend or terminate its
tasks. When expired, the Wait mode is exited for User Off mode or Memory Hold mode, depending on warm starts being enabled
or not via the WARMEN bit. The USEROFFSPI bit is being reset at this point by RESETB going low.
Memory Hold and User Off (Low-power Off states)
As noted in the User Off Wait description, the system is directed into Low-power Off states based on a SPI command in
response to an intentional turn off by the end user. The only exit then will be a turn on event. To an end user, the Memory Hold
and User Off states look like the product has been shut down completely. However, a faster startup is facilitated by maintaining
external memory in self-refresh mode (Memory Hold and User Off mode) as well as powering portions of the processor core for
state retention (User Off only). The switcher mode control bits allow selective powering of the buck regulators for optimizing the
supply behavior in the Low-power Off modes. Linear regulators and most functional blocks are disabled (the RTC module, and
Turn On event detection are maintained).
Memory Hold
RESETB and RESETBMCU are low, and both CLK32K and CLK32KMCU are disabled. If DRM is set, the CLK32KMCU is
kept active. To ensure that SW1, SW2, and SW3 shut off in Memory Hold, appropriate mode settings should be used such as
SW1MHMODE = SW2MHMODE = SW3MHMODE = 0 (refer to the mode control description later in this chapter). Since SW4
should be powered in PFM mode, SW4MHMODE could be set to 1.
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
57
相关PDF资料 |
PDF描述 |
|---|---|
| ECM15DTAS | CONN EDGECARD 30POS R/A .156 SLD |
| GBM25DRTN-S13 | CONN EDGECARD 50POS .156 EXTEND |
| AK670M-5-R | CABLE MINI USB 4PIN 5M 1.1 VERS |
| EEM28DSXI | CONN EDGECARD 56POS DIP .156 SLD |
| MC13892JVKR2 | IC PMU I.MX51/37/35/27 139MAPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC13892VK | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VKR2 | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VL | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VLR2 | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC1-38RX | 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL |
发布紧急采购，3分钟左右您将得到回复。