参数资料
型号: MC13892JVLR2
厂商: Freescale Semiconductor
文件页数: 89/158页
文件大小: 0K
描述: IC PMU I.MX51/37/35/27 186MAPBGA
标准包装: 1,000
应用: 电池管理,显示器(LED 驱动器),手持/移动设备,电源
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 186-LFBGA
供应商设备封装: 186-PBGA(12x12)
包装: 带卷 (TR)
FUNCTIONAL DEVICE OPERATION
BATTERY INTERFACE AND CONTROL
BATTERY INTERFACE AND CONTROL
The battery management interface is optimized for applications with a single charger connector to which a standard wall
charger or a USB host can be connected. It can also support dead battery operation and unregulated chargers.
CHARGE PATH
CHARGER LINE UP
The charge path is depicted in the following diagram.
Figure 26. Charge Path Block Diagram
Transistors M1 and M2 control the charge current and provide voltage regulation. The latter is used as the top off change
voltage, and as the regulated supply voltage to the application in case of a dead battery operation. In order to support dead
battery operation, a so called “serial path” charging configuration including M3 needs to be used. Then in case of a dead battery,
the transistor M3 is made non-conducting and the internal trickle charge current charges the battery. If the battery is sufficiently
charged, the transistor M3 is made conducting which connects the battery to the application just like during normal operation
without a charger. In so called single path charging, M3 is replaced by a short and the pin BATTFET must be floating. Dead
battery operation is not supported in this case. Transistors M1 and M2 become non-conducting if the charger voltage is too high.
The VBUS must be shorted to CHRGRAW in cases where the wall charger and VBUS voltages are contained on a common pin.
A current can be supplied from the battery to an accessory with all transistors M1, M2, and M3 conducting, by enabling the
reverse supply mode. An unregulated wall charger configuration can be built, in which case CHRGSE1B must be pulled low. The
battery current monitoring resistor R1 and the charge LED indicator are optional. More detail on the battery current monitoring
can be found in ADC Subsystem .
The preferred devices for M1 and M2 are Fairchild? FDZ193P, due to their small package outline and thermal characteristics.
The preferred device for M3 is the On Semiconductor NTHS2101P for its low R DSON and small footprint.
CHARGER SIGNALS
The charger uses a number of thresholds for proper operation and will also signal various events to the processor through
interrupts. Table 61 summarizes the main signals given, including the control bits. For details see the related sections in this
chapter and the SPI bit summary in SPI Bitmap .
Table 61. Main Control Bit Signals
Name
Control Bits
VCHRG[2:0]
ICHRG[3:0]
TREN
Charger regulator voltage setting
Charger regulator current setting
Internal trickle charger enabling
Description
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
89
相关PDF资料
PDF描述
ECM15DTAS CONN EDGECARD 30POS R/A .156 SLD
GBM25DRTN-S13 CONN EDGECARD 50POS .156 EXTEND
AK670M-5-R CABLE MINI USB 4PIN 5M 1.1 VERS
EEM28DSXI CONN EDGECARD 56POS DIP .156 SLD
MC13892JVKR2 IC PMU I.MX51/37/35/27 139MAPBGA
相关代理商/技术参数
参数描述
MC13892VK 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VKR2 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VL 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC13892VLR2 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MC1-38RX 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL