- 您现在的位置：买卖IC网 > PDF目录16590 > MC13892JVLR2 (Freescale Semiconductor)IC PMU I.MX51/37/35/27 186MAPBGA PDF资料下载
参数资料
| 型号： | MC13892JVLR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 52/158页 |
| 文件大小： | 0K |
| 描述： | IC PMU I.MX51/37/35/27 186MAPBGA |
| 标准包装： | 1,000 |
| 应用： | 电池管理，显示器（LED 驱动器），手持/移动设备，电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 186-LFBGA |
| 供应商设备封装： | 186-PBGA（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
CLOCK GENERATION AND REAL TIME CLOCK
TIME OF DAY ALARM
A Time Of Day Alarm (TODA) function can be used to turn on the application and alert the processor. If the application is
already on, the processor will be interrupted. The TODA and DAYA registers are used to set the alarm time. Only a single alarm
can be programmed at a time. When the TOD counter is equal to the value in TODA, and the DAY counter is equal to the value
in DAYA, the TODAI interrupt will be generated.
At initial power up of the application (application of the coin cell), the state of the TODA and DAYA registers will be all 1's. The
interrupt for the alarm (TODAI) is backed up by LICELL and will be valid at power up. If the mask bit for the TOD alarm (TODAM)
is high, then the TODAI interrupt is masked and the application will not turn on with the time of day alarm event
(TOD[16:0] = TODA[16:0] and DAY[14:0] = DAYA[14:0]). By default, the TODAM mask bit is set to 1, thus masking the interrupt
and turn on event.
TIMER RESET
As long as the supply at BP is valid, the real time clock will be supplied from VCORE. If not, it can be backed up from a coin
cell via the LICELL pin. When the backup voltage drops below RTCUVDET, the RTCPORB reset signal is generated and the
contents of the RTC will be reset. Additional registers backed up by coin cell will also reset with RTCPORB. To inform the
processor that the contents of the RTC are no longer valid due to the reset, a timer reset interrupt function is implemented with
the RTCRSTI bit.
RTC TIMER CALIBRATION
A clock calibration system is provided to adjust the 32,768 cycle counter that generates the 1.0 Hz timer for RTC timing
registers to comply with digital rights management specifications of ±50 ppm. This calibration system can be disabled, if not
needed to reduce the RTC current drain. The general implementation relies on the system processor to measure the 32.768 kHz
crystal oscillator against a higher frequency and more accurate system clock such as a TCXO. If the RTC timer needs a
correction, a 5-bit 2's complement calibration word can be sent via the SPI to compensate the RTC for inaccuracy in its reference
Table 18. RTC Calibration Settings
Code in RTCCAL[4:0]
01111
00011
00001
00000
11111
11101
10001
10000
Correction in Counts per 32768
+15
+3
+1
0
-1
-3
-15
-16
Relative correction in ppm
+458
+92
+31
0
-31
-92
-458
-488
Note that the 32.768 kHz oscillator is not affected by RTCCAL settings. Calibration is only applied to the RTC time base
counter. Therefore, the frequency at the clock outputs CLK32K and CLK32KMCU are not affected.
The RTC system calibration is enabled by programming the RTCCALMODE[1:0] for desired behavior by operational mode.
Table 19. RTC Calibration Enabling
RTCCALMODE
00
01
10
11
Function
RTC Calibration disabled (default)
RTC Calibration enabled in all modes except coin cell only
Reserved for future use. Do not use.
RTC Calibration enabled in all modes
A slight increase in consumption will be seen when the calibration circuitry is activated. To minimize consumption and
maximize lifetime when the RTC system is maintained by the coin cell, the RTC Calibration circuitry can be automatically disabled
when main battery contact is lost, or if it is so deeply discharged that RTC power draw is switched to the coin cell (configured
with RTCCALMODE = 01).
Because of the low RTC consumption, RTC accuracy can be maintained through long periods of the application being shut
down, even after the main battery has discharged. However, it is noted that the calibration can only be as good as the RTCCAL
MC13892
Analog Integrated Circuit Device Data
52
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| ECM15DTAS | CONN EDGECARD 30POS R/A .156 SLD |
| GBM25DRTN-S13 | CONN EDGECARD 50POS .156 EXTEND |
| AK670M-5-R | CABLE MINI USB 4PIN 5M 1.1 VERS |
| EEM28DSXI | CONN EDGECARD 56POS DIP .156 SLD |
| MC13892JVKR2 | IC PMU I.MX51/37/35/27 139MAPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC13892VK | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VKR2 | 功能描述:PMIC 解决方案 PMUIC w/4 buck/12 LDO rg RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VL | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC13892VLR2 | 功能描述:PMIC 解决方案 5/28V BCK/BST PMUIC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC1-38RX | 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL |
发布紧急采购，3分钟左右您将得到回复。