- 您现在的位置：买卖IC网 > PDF目录225025 > RC28F256P33T85A (NUMONYX) 16M X 16 FLASH 3V PROM, 85 ns, PBGA64 PDF资料下载
参数资料
| 型号： | RC28F256P33T85A |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 16M X 16 FLASH 3V PROM, 85 ns, PBGA64 |
| 封装： | BGA-64 |
| 文件页数： | 58/96页 |
| 文件大小： | 1378K |
| 代理商： | RC28F256P33T85A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
November 2007
Datasheet
Order Number: 314749-05
61
Numonyx StrataFlash Embedded Memory (P33)
stored to sequential buffer locations starting at address 0x00. Programming of the
buffer contents to the flash memory array starts as soon as the buffer is full. If the
number of words is less than 32, the remaining buffer locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an
address outside of the current block's range during a buffer-fill sequence
causes the algorithm to exit immediately. Any data previously loaded into the
buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the BEFP
algorithm will be aborted and the program fails and (SR[4]) flag will be set.
Data words from the write buffer are directed to sequential memory locations in the
flash memory array; programming continues from where the previous buffer sequence
ended. The host programming system must poll SR[0] to determine when the buffer
program sequence completes. SR[0] cleared indicates that all buffer data has been
transferred to the flash array; SR[0] set indicates that the buffer is not available yet for
the next fill cycle. The host system may check full status for errors at any time, but it is
only necessary on a block basis after BEFP exit. After the buffer fill cycle, no write
cycles should be issued to the device until SR[0] = 0 and the device is ready for the
next buffer fill.
Note:
Any spurious writes are ignored after a buffer fill operation and when internal program
is proceeding.
The host programming system continues the BEFP algorithm by providing the next
group of data words to be written to the buffer. Alternatively, it can terminate this
phase by changing the block address to one outside of the current block’s range.
The Program/Verify phase concludes when the programmer writes to a different block
address; data supplied must be 0xFFFF. Upon Program/Verify phase completion, the
device enters the BEFP Exit phase.
11.3.3.4
BEFP Exit Phase
When SR[7] is set, the device has returned to normal operating conditions. A full status
check should be performed at this time to ensure the entire block programmed
successfully. When exiting the BEFP algorithm with a block address change, the read
mode will not change. After BEFP exit, any valid command can be issued to the device.
11.3.4
Program Suspend
Issuing the Program Suspend command while programming suspends the
programming operation. This allows data to be accessed from the device other than the
one being programmed. The Program Suspend command can be issued to any device
address. A program operation can be suspended to perform reads only. Additionally, a
program operation that is running during an erase suspend can be suspended to
perform a read operation (see Figure 34, “Program Suspend/Resume Flowchart” on
page 70).
When a programming operation is executing, issuing the Program Suspend command
requests the WSM to suspend the programming algorithm at predetermined points. The
device continues to output Status Register data after the Program Suspend command is
issued. Programming is suspended when Status Register bits SR[7,2] are set. Suspend
latency is specified in Section 7.5, “Program and Erase Characteristics” on page 39.
To read data from the device, the Read Array command must be issued. Read Array,
Read Status Register, Read Device Identifier, CFI Query, and Program Resume are valid
commands during a program suspend.
相关PDF资料 |
PDF描述 |
|---|---|
| RC28F160C3TC90 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA64 |
| RC28F160C3BD70 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA64 |
| RC4194K | DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9 |
| RM4194K | DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9 |
| RC4194D | DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, CDIP14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RC28F256P33T85B | 制造商:Micron Technology Inc 功能描述:256MB, KEARNY EBGA 3.0 - Tape and Reel |
| RC28F256P33TFA | 功能描述:IC FLASH 256MBIT 95NS 64EZBGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:Axcell™ 产品变化通告:Product Discontinuation 26/Apr/2010 标准包装:136 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步，DDR II 存储容量:18M（1M x 18） 速度:200MHz 接口:并联 电源电压:1.7 V ~ 1.9 V 工作温度:0°C ~ 70°C 封装/外壳:165-TBGA 供应商设备封装:165-CABGA（13x15） 包装:托盘 其它名称:71P71804S200BQ |
| RC28F256P33TFE | 功能描述:IC FLASH 256MBIT 64EZBGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:Axcell™ 标准包装:72 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步 存储容量:4.5M（256K x 18） 速度:133MHz 接口:并联 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x20） 包装:托盘 |
| RC28F320C3 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY |
| RC28F320C3BA100 | 功能描述:IC FLASH 32MBIT 100NS 64BGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:150 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (2 x 256 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-DFN（2x3） 包装:管件 产品目录页面:1445 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。