- 您现在的位置：买卖IC网 > PDF目录69322 > RK80532RC056128 (INTEL CORP) 2400 MHz, MICROPROCESSOR, CPGA478 PDF资料下载
参数资料
| 型号： | RK80532RC056128 |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 2400 MHz, MICROPROCESSOR, CPGA478 |
| 封装： | FLIP CHIP, PGA2-478 |
| 文件页数： | 75/99页 |
| 文件大小： | 4142K |
| 代理商： | RK80532RC056128 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页当前第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
Datasheet
77
Pin Listing and Signal Definitions
PROCHOT#
Input/
Output
As an output, PROCHOT# (Processor Hot) will go active when the processor
temperature monitoring sensor detects that the processor has reached its
maximum safe operating temperature. This indicates that the processor Thermal
Control Circuit has been activated, if enabled. As an input, assertion of
PROCHOT# by the system will activate the TCC, if enabled. The TCC will remain
active until the system deasserts PROCHOT#. See Section 7.3 for more details.
NOTE:
The PROCHOT# signal is input/output only on CPUID 0xF27 and
beyond; otherwise, it is an output signal.
PWRGOOD
Input
PWRGOOD (Power Good) is a processor input. The processor requires this
signal to be a clean indication that the clocks and power supplies are stable and
within their specifications. ‘Clean’ implies that the signal will remain low (capable
of sinking leakage current), without anomalies, from the time that the power
supplies are turned on until they come within specification. The signal must then
transition monotonically to a high state. Figure 14 illustrates the relationship of
PWRGOOD to the RESET# signal. PWRGOOD can be driven inactive at any
time, but clocks and power must again be stable before a subsequent rising edge
of PWRGOOD. It must also meet the minimum pulse width specification in
Table 19, and be followed by a 1 to 10 ms RESET# pulse.
The PWRGOOD signal must be supplied to the processor; it is used to protect
internal circuits against voltage sequencing issues. It should be driven high
throughout boundary scan operation.
REQ[4:0]#
Input/
Output
REQ[4:0]# (Request Command) must connect the appropriate pins of all
processor system bus agents. They are asserted by the current bus owner to
define the currently active transaction type. These signals are source
synchronous to ADSTB0#. Refer to the AP[1:0]# signal description for details on
parity checking of these signals.
RESET#
Input
Asserting the RESET# signal resets the processor to a known state and
invalidates its internal caches without writing back any of their contents. For a
power-on Reset, RESET# must stay active for at least one millisecond after VCC
and BCLK have reached their proper specifications. On observing active
RESET#, all system bus agents will deassert their outputs within two clocks.
RESET# must not be kept asserted for more than 10 ms while PWRGOOD is
asserted.
A number of bus signals are sampled at the active-to-inactive transition of
RESET# for power-on configuration. These configuration options are described
in the Section 7.1.
NOTE:
This signal does not have on-die termination and must be terminated on
the system board.
RS[2:0]#
Input
RS[2:0]# (Response Status) are driven by the response agent (the agent
responsible for completion of the current transaction), and must connect the
appropriate pins of all processor system bus agents.
RSP#
Input
RSP# (Response Parity) is driven by the response agent (the agent responsible
for completion of the current transaction) during assertion of RS[2:0]#, the
signals for which RSP# provides parity protection. It must connect to the
appropriate pins of all processor system bus agents.
A correct parity signal is high if an even number of covered signals are low, and
low if an odd number of covered signals are low. While RS[2:0]# = 000, RSP# is
also high, since this indicates it is not being driven by any agent guaranteeing
correct parity.
SKTOCC#
Output
SKTOCC# (Socket Occupied) will be pulled to ground by the processor. System
board designers may use this pin to determine if the processor is present.
Table 36. Signal Description (Sheet 6 of 8)
Name
Type
Description
相关PDF资料 |
PDF描述 |
|---|---|
| RK80546KG0882MM | 64-BIT, 3200 MHz, MICROPROCESSOR, CPGA604 |
| RK80546KG1042MM | 64-BIT, 3600 MHz, MICROPROCESSOR, CPGA604 |
| RK80546KG0802MM | 64-BIT, 3000 MHz, MICROPROCESSOR, CPGA604 |
| RK80546PG0801M | 32-BIT, 3000 MHz, MICROPROCESSOR, CPGA478 |
| RK80546PE0721M | 32-BIT, 2800 MHz, MICROPROCESSOR, CPGA478 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RK80532RC060128S L6ZY | 制造商:Intel 功能描述:MPU Celeron? Processor 0.13um 2.5GHz 478-Pin FCPGA2 制造商:Intel 功能描述:NORTHWOOD; MPU CELERON 0.13UM 2.5GHZ 478PIN FCPGA2 - Trays |
| RK80532RC060128SL72B | 功能描述:IC CELERON 2.5GHZ 478FC-PGA2 RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:- 标准包装:2 系列:MPC8xx 处理器类型:32-位 MPC8xx PowerQUICC 特点:- 速度:133MHz 电压:3.3V 安装类型:表面贴装 封装/外壳:357-BBGA 供应商设备封装:357-PBGA（25x25） 包装:托盘 |
| RK80532RC064128 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| RK805346RE067256 | 制造商:Intel 功能描述:TRAY CELERON D 330 - Trays |
| RK80546KF0871M | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。