参数资料
型号: SX1211I084TRT
厂商: Semtech
文件页数: 19/92页
文件大小: 0K
描述: IC SNGL-CHIP TXRX 32-TQFN
标准包装: 1
频率: 860 ~ 960MHz
数据传输率 - 最大: 200kbps
调制或协议: FSK,OOK
应用: AMR,ISM,安防门禁
功率 - 输出: 12.5dBm
灵敏度: -113dBm
电源电压: 2.1 V ~ 3.6 V
电流 - 接收: 3mA
电流 - 传输: 25mA
数据接口: PCB,表面贴装
天线连接器: PCB,表面贴装
工作温度: -40°C ~ 85°C
封装/外壳: 32-TQFN
包装: 标准包装
产品目录页面: 584 (CN2011-ZH PDF)
配用: 1210-1060-2-ND - 915MHZ ASPICS SX1211 CHIP SET
1210-1059-2-ND - 868MHZ ASPICS SX1211 CHIP SET
1210-1060-6-ND - 915MHZ ASPICS SX1211 CHIP SET
1210-1059-6-ND - 868MHZ ASPICS SX1211 CHIP SET
1210-1060-1-ND - 915MHZ ASPICS SX1211 CHIP SET
1210-1059-1-ND - 868MHZ ASPICS SX1211 CHIP SET
其它名称: SX1211I084DKR
SX1211
WIRELESS & SENSING
In OOK mode, the phase difference between the I and Q channels is kept constant (independent of the transmitted
data). Thus, the first stage of up-conversion creates a fixed frequency signal at the low IF = Fdev (This explains
why the transmitted OOK spectrum is offset by Fdev).
OOK Modulation is accomplished by switching on and off the PA and PA regulator stages. By convention:
DATA = ' ' 1 ' ' ? PAon
DATA = ' ' 0 ' ' ? PAoff
After the interpolation filters, a set of four mixers combines the I and Q signals and converts them into a pair of
complex signals at the second intermediate frequency, equal to 1/8 of the LO frequency, or 1/9 of the RF
frequency. These two new I and Q signals are then combined and up-converted to the final RF frequency by two
quadrature mixers fed by the LO signal. The signal is pre-amplified, and then the transmitter output is driven by a
final power amplifier stage.
3.3.2. Bit Rate Setting
In Continuous transmit mode, setting the Bit Rate is useful to determine the frequency of DCLK. As explained in
section 5.3.2, DCLK will trigger an interrupt on the uC each time a new bit has to be transmitted.
BR =
F XTAL
64 * [ 1 + val ( MCParam _ BR ) ]
3.3.3. Alternative Settings
Bit rate, frequency deviation and TX interpolation filter settings are a function of the reference oscillator crystal
frequency, F XTAL . Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of
the correct reference oscillator frequency. Please contact your local Semtech representative for further details.
3.3.4. Fdev Setting in FSK Mode
The frequency deviation, Fdev, of the FSK transmitter is programmed through bits MCParam_Freq_dev:
Fdev =
F XTAL
32 * [ 1 + val ( MCParam _ Freq _ dev ) ]
For correct operation the modulation index ? should be such that:
β = 2 *
Fdev
BR
≥ 2
It should be noted that for communications between a pair of SX1211s, that Fdev should be at least 33 kHz to
ensure a correct operation on the receiver side.
3.3.5. Fdev Setting in OOK Mode
Fdev has no physical meaning in OOK transmit mode. However, as has been shown - due to the DDS baseband
signal generation, the OOK signal is always offset by “-Fdev” (see formulas is section 3.2.8). It is suggested that
Fdev retains its default value of 100 kHz in OOK mode.
Rev 8 – February 2013
Page 19 of 92
www.semtech.com
相关PDF资料
PDF描述
12-900-LPI XFRMR PWR 115/230V 12.6VCT 900MA
10-1200-LPI XFRMR PWR 115/230V 10VCT 1.2A
MT-6-12 XFRMR 115V 5V 1.75A 6VA 3OUT
ATMEGA64RZAV-10MU MCU ATMEGA644/AT86RF230 44-QFN
ATMEGA128RFA1-ZU IC AVR MCU 2.4GHZ XCEIVER 64QFN
相关代理商/技术参数
参数描述
SX1211I084TRT 制造商:Semtech Corporation 功能描述:GPSS WL SKU APP1
SX1211I084TRT-CUT 制造商:Semtech Corporation 功能描述:
SX1211I097.TRT 制造商:Semtech Corporation 功能描述:
SX1211MESH-868 制造商:Semtech Corporation 功能描述:10 MODULES MESH NETWORK
SX1211SK868 制造商:Semtech Corporation 功能描述:Full Evalulation Kit For Ultra-Low Power Integrated UHF Transceiver