- 您现在的位置：买卖IC网 > PDF目录18758 > SX1211I084TRT (Semtech)IC SNGL-CHIP TXRX 32-TQFN PDF资料下载
参数资料
| 型号： | SX1211I084TRT |
| 厂商： | Semtech |
| 文件页数： | 52/92页 |
| 文件大小： | 0K |
| 描述： | IC SNGL-CHIP TXRX 32-TQFN |
| 标准包装： | 1 |
| 频率： | 860 ~ 960MHz |
| 数据传输率 - 最大： | 200kbps |
| 调制或协议： | FSK，OOK |
| 应用： | AMR，ISM，安防门禁 |
| 功率 - 输出： | 12.5dBm |
| 灵敏度： | -113dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 3mA |
| 电流 - 传输： | 25mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-TQFN |
| 包装： | 标准包装 |
| 产品目录页面： | 584 (CN2011-ZH PDF) |
| 配用： | 1210-1060-2-ND - 915MHZ ASPICS SX1211 CHIP SET 1210-1059-2-ND - 868MHZ ASPICS SX1211 CHIP SET 1210-1060-6-ND - 915MHZ ASPICS SX1211 CHIP SET 1210-1059-6-ND - 868MHZ ASPICS SX1211 CHIP SET 1210-1060-1-ND - 915MHZ ASPICS SX1211 CHIP SET 1210-1059-1-ND - 868MHZ ASPICS SX1211 CHIP SET |
| 其它名称： | SX1211I084DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
SX1211
WIRELESS & SENSING
By default, if the CRC check is enabled and fails for the current packet, then the FIFO is automatically cleared and
neither of the two interrupts are generated and new packet reception is started. This autoclear function can be
disabled via PKTParam_CRC_autoclr bit and, in this case, even if CRC fails, the FIFO is not cleared and only
Payload_ready IRQ source is asserted.
Once fully received, the payload can also be fully or partially retrieved in Stby mode via
PKTParam_Fifo_stby_access. At the end of the reception, although the FIFO automatically stops being filled, it is
still up to the user to explicitly exit Rx mode if required. (e.g. go to Stby to get payload). FIFO must be empty for a
new packet reception to start.
5.5.5. Packet Filtering
SX1211’s packet handler offers several mechanisms for packet filtering ensuring that only useful packets are made
available to the uC, reducing significantly system power consumption and software complexity.
5.5.5.1. Sync Word Based
Sync word filtering/recognition is automatically enabled in Packet mode. It is used for identifying the start of the
payload and also for network identification. As previously described, the Sync word recognition block is configured
(size, error tolerance, value) via RXParam_Sync_size, RXParam_Sync_tol and SYNCParam configuration
registers. This information is used, both for appending Sync word in Tx, and filtering packets in Rx.
Every received packet which does not start with this locally configured Sync word is automatically discarded and no
interrupt is generated.
When the Sync word is detected, payload reception automatically starts and Sync IRQ source is asserted.
5.5.5.2. Address Based
Address filtering can be enabled via the PKTParam_Adrs_filt bits. It adds another level of filtering, above Sync
word, typically useful in a multi-node networks where a network ID is shared between all nodes (Sync word) and
each node has its own ID (address).
Three address based filtering options are available:
Adrs_filt = 01: Received address field is compared with internal register Node_Adrs. If they match then the
packet is accepted and processed, otherwise it is discarded.
Adrs_filt = 10: Received address field is compared with internal register Node_Adrs and the constant 0x00. If
either is a match, the received packet is accepted and processed, otherwise it is discarded. This additional
check with a constant is useful for implementing broadcast in a multi-node networks.
Adrs_filt = 11: Received address field is compared with internal register Node_Adrs and the constants 0x00 &
0xFF. If any of the three matches, then the received packet is accepted and processed, otherwise it is
discarded. These additional checks with constants are useful for implementing broadcast commands of all
nodes.
Please note that the received address byte, as part of the payload, is not stripped off the packet and is made
available in the FIFO. In addition, Node_Adrs and Adrs_filt only apply to Rx. On Tx side, if address filtering is
expected, the address byte should simply be put into the FIFO like any other byte of the payload.
5.5.5.3. Length Based
In variable length Packet mode, PKTParam_Payload_length must be programmed with the maximum length
permitted. If received length byte is smaller than this maximum then the packet is accepted and processed,
otherwise it is discarded.
Rev 8 – February 2013
Page 52 of 92
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| 12-900-LPI | XFRMR PWR 115/230V 12.6VCT 900MA |
| 10-1200-LPI | XFRMR PWR 115/230V 10VCT 1.2A |
| MT-6-12 | XFRMR 115V 5V 1.75A 6VA 3OUT |
| ATMEGA64RZAV-10MU | MCU ATMEGA644/AT86RF230 44-QFN |
| ATMEGA128RFA1-ZU | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SX1211I084TRT | 制造商:Semtech Corporation 功能描述:GPSS WL SKU APP1 |
| SX1211I084TRT-CUT | 制造商:Semtech Corporation 功能描述: |
| SX1211I097.TRT | 制造商:Semtech Corporation 功能描述: |
| SX1211MESH-868 | 制造商:Semtech Corporation 功能描述:10 MODULES MESH NETWORK |
| SX1211SK868 | 制造商:Semtech Corporation 功能描述:Full Evalulation Kit For Ultra-Low Power Integrated UHF Transceiver |
发布紧急采购，3分钟左右您将得到回复。