- 您现在的位置：买卖IC网 > PDF目录18751 > TRC103 (RFM)RFIC TRANSCEIVER MULTI-CHANNEL F PDF资料下载
参数资料
| 型号： | TRC103 |
| 厂商： | RFM |
| 文件页数： | 22/65页 |
| 文件大小： | 0K |
| 描述： | RFIC TRANSCEIVER MULTI-CHANNEL F |
| 标准包装： | 1 |
| 系列： | TRC |
| 频率： | 863MHz ~ 960MHz |
| 数据传输率 - 最大： | 100kbps |
| 调制或协议： | FSK，OOK |
| 应用： | 通用 |
| 功率 - 输出： | 11dBm |
| 灵敏度： | -112dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 4mA |
| 电流 - 传输： | 30mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-QFN |
| 包装： | 标准包装 |
| 产品目录页面： | 583 (CN2011-ZH PDF) |
| 其它名称： | 583-1095-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
3.9.4 Packet Payload Processing in Transmit and Receive
The TRC103 packet handler constructs transmit packets using the payload bytes in the FIFO. In receive, it pro-
cesses the packets and extracts the payload bytes to the FIFO. Packet processing in transmit and receive are
detailed below.
For transmit, the packet handler adds the following fields and processing to the payload in the FIFO:
1. One to four programmable preamble bytes
2. One to four start pattern bytes, programmable and usually set to at least 2 bytes
3. Optional CRC checksum calculated over the FIFO payload and appending to the end of the packet
4. Optional Manchester encoding or DC-balanced scrambling
The payload in the FIFO may contain one or both of the following optional fields:
1. A length byte if the variable packet length mode is selected
2. A node address byte
The way transmission is initiated depends on the configuration set by the user and the value of the
IRQCFG0E_Start_Full[4] bit.
If the FIFO is filled while transmit mode is enabled, and if IRQCFG0E_Start_Full[4] is set to 1, the modulator
waits until the first byte is written into the FIFO, then it starts sending the programmed preamble bytes followed by
the start pattern and the user payload. If IRQCFG0E_Start_Full[4 ] is set to 0 in the same conditions, the modu-
lator waits until the number of bytes written in the FIFO is equal to the number defined in the register MCFG05_
FIFO_thresh[5..0] . Note that the transmitter automatically sends preamble bytes in addition the number pro-
grammed while in transmit mode and waiting for the FIFO to receive the required number of bytes to start data
transmission. Data to be transmitted can also be written into the FIFO during standby mode. In this case, the data
is automatically transmitted when the transmit mode is enabled and the transmitter reaches its steady state.
If CRC is enabled, the CRC checksum is calculated over the payload bytes. This 16-bit checksum is sent after the
bytes in the FIFO. If CRC is enabled, the TX_STOP bit is set when the last CRC bit is transferred to the TX modu-
lator. If CRC is not enabled, the TX_STOP bit is set when the last bit from the FIFO is transferred to the TX modu-
lator. Note that the transmitter must remain on one bit period after the TX_STOP bit is set while the last bit is be-
ing transmitted. If the transmitter remains on following the transmission of the last bit after TX_STOP is set, the
transmitter will send preamble bytes. If Manchester encoding or scrambling is enabled, all data except the pream-
ble and start pattern is encoded or scrambled before transmission. Note that the length byte in the FIFO deter-
mines the length of the packet to be sent and the PKTCFG1C_Pkt_len[6..0] parameter is not used in transmit.
In receive the packet handler retrieves the payload by performing the following steps:
1. Data and clock recovery synchronization to the preamble
2. Start pattern detection
3. Optional address byte check
4. Error detection through CRC
When receive mode is enabled, the demodulator detects the preamble followed by the start pattern. If fixed length
packet format is enabled, then the number of bytes received as the payload is given by the PKTCFG1C_Pkt_
len[6..0] parameter.
In variable length and extended variable length packet modes, the first byte received after the start pattern
is interpreted as the length of the balance of the payload. An internal length counter is initialized to this length.
The PKTCFG1C_Pkt_len[6..0] register must be set to a value which is equal to or greater than the maximum
www.RFM.com E-mail: info@rfm.com
? 2009-2010 by RF Monolithics, Inc.
Technical support +1.800.704.6079
Page 22 of 65
TRC103 - 11/29/12
相关PDF资料 |
PDF描述 |
|---|---|
| UPC8179TB-A | IC AMPLIFIER LOW CURRENT SOT363 |
| UPC8178TB-E3-A | IC AMPLIFIER LOW CURRENT SOT363 |
| DP-241-7-16 | XFRMR PWR 115/230V 16VCT 3.5A |
| UPC8178TB-A | IC AMPLIFIER LOW CURRENT SOT363 |
| UPC2771TB-A | MMIC AMP 3V 2.4GHZ SOT363 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TRC1036 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
| TRC104 | 功能描述:射频收发器 Transceiver 2.4 GHz Multi-channel GFSK RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| TRC1044 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
| TRC105 | 功能描述:射频收发器 Transceiver 300-510 MHz, Multi-chnl FSK RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| TRC1053 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
发布紧急采购，3分钟左右您将得到回复。