- 您现在的位置：买卖IC网 > PDF目录18751 > TRC103 (RFM)RFIC TRANSCEIVER MULTI-CHANNEL F PDF资料下载
参数资料
| 型号： | TRC103 |
| 厂商： | RFM |
| 文件页数： | 61/65页 |
| 文件大小： | 0K |
| 描述： | RFIC TRANSCEIVER MULTI-CHANNEL F |
| 标准包装： | 1 |
| 系列： | TRC |
| 频率： | 863MHz ~ 960MHz |
| 数据传输率 - 最大： | 100kbps |
| 调制或协议： | FSK，OOK |
| 应用： | 通用 |
| 功率 - 输出： | 11dBm |
| 灵敏度： | -112dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 4mA |
| 电流 - 传输： | 30mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-QFN |
| 包装： | 标准包装 |
| 产品目录页面： | 583 (CN2011-ZH PDF) |
| 其它名称： | 583-1095-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页
23. Place TRC103 in transmit mode by setting MCFG00 bits 7..5 set to 100. Monitor IRQ1. It sets when the
when the last bit starts to be transmitted. Allow one bit period for the last bit to be transmitted and then
switch to standby mode by setting MCFG00 bits 7..5 to 001.
24. When ready to receive, Place the TRC103 in synthesizer mode by setting MCFG00 bits 7..5 set to 010.
Monitor the TRC103 Pin 23 to confirm PLL lock.
25. Switch from synthesizer mode to receive mode by setting MCFG00 bits 7..5 to 011.
26. Monitor IRQ0. When an error free packet is received addressed to this node, IRQ0 will set.
27. Switch the TRC103 to standby mode by setting MCFG00 bits 7..5 to 001.
28. Set bit 6 to 1 in PKTCFG1F to enable FIFO read in standby mode.
29. Retrieve the received data from the FIFO through the SPI port.
30. From standby mode, enter another transmit cycle as outlined in steps 20 through 23, or enter another
receive cycle as outlined in steps 24 through 30.
6.7 Battery Power Management Configuration Values
Battery life can be greatly extended in TRC103 applications where transmissions from field nodes are infrequent,
or network communications can be concentrated in periodic time slots. For example, field nodes in many wireless
alarm systems report operational status a few times a day, and can otherwise sleep unless an alarm condition
occurs. Sensor networks that monitor parameters that change relatively slowly, such as air and soil temperature
in agricultural settings, only need to transmit updates a few times an hour.
At room temperature the TRC103 draws a maximum of 1 μA in sleep mode, with a typical value of 100 nA. To
achieve minimum sleep mode current, nSS_CONFIG (Pin 14), SDI (Pin 17) and SCK (Pin 18) must be held logic
low, while nSS_DATA (Pin 15) must be held logic high. Also, the external connection to SDO (Pin 16) must be
configured as high impedance (tri-state or input). The TRC103 can go from sleep mode through standby mode
and synthesizer mode to transmit (or receive) mode in less than 6 ms. At a data rate of 33.33 kb/s, a 32 byte
packet with a 4 byte preamble and a 4 byte start pattern takes about 10 ms to transmit. Assume that the TRC103
then switches to receive mode for 1 second to listen for a response and returns to sleep. On the basis of reporting
every six hours, the ON to sleep duty cycle is about 1:21,259, greatly extending battery life over continuous
transmit-receive or even standby operation. RFM provides an Excel spreadsheet, battery_ life_ calculator.xls, in
the Application Notes section of www.RFM.com to support battery life for various operating scenarios.
The required timing accuracy for the microcontrollers in a sleep-cycled application depends on several things:
?
?
?
The required “time-stamp” accuracy of data reported by sleeping field nodes. R-C sleep mode timers built
into many microcontrollers have a tolerance of ±20% or more. Where more accurate time stamping is re-
quired, many microcontrollers can run on a watch crystal during sleep and achieve time stamp accuracies
better than one second per 24 hours.
If the base station and any routing nodes present in a network must sleep cycle in addition to the field
nodes, watch crystal control will usually be needed to keep all nodes accurately synchronized to the ac-
tive time slots.
If the base station and any routing nodes present in a network can operate continuously (AC powered,
solar charged batteries, etc.) and a loose time stamp accuracy is OK, the microcontrollers in sleeping field
nodes can usually operated from internal low-accuracy R-C timers.
www.RFM.com E-mail: info@rfm.com
? 2009-2010 by RF Monolithics, Inc.
Technical support +1.800.704.6079
Page 61 of 65
TRC103 - 11/29/12
相关PDF资料 |
PDF描述 |
|---|---|
| UPC8179TB-A | IC AMPLIFIER LOW CURRENT SOT363 |
| UPC8178TB-E3-A | IC AMPLIFIER LOW CURRENT SOT363 |
| DP-241-7-16 | XFRMR PWR 115/230V 16VCT 3.5A |
| UPC8178TB-A | IC AMPLIFIER LOW CURRENT SOT363 |
| UPC2771TB-A | MMIC AMP 3V 2.4GHZ SOT363 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TRC1036 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
| TRC104 | 功能描述:射频收发器 Transceiver 2.4 GHz Multi-channel GFSK RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| TRC1044 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
| TRC105 | 功能描述:射频收发器 Transceiver 300-510 MHz, Multi-chnl FSK RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| TRC1053 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:10/100M Single Port Transformer Modules |
发布紧急采购，3分钟左右您将得到回复。