参数资料
| 型号： | ADT7468ZEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 21/81页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADT7468 |
| 标准包装： | 1 |
| 其它名称： | EVAL-ADT7468EB EVAL-ADT7468EB-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页
ADT7468
Temperature Measurement Limit Registers
Table 10. Conversion Time with Averaging Enabled
Each temperature measurement channel is associated with high
and low limit registers. Exceeding the programmed high or low
limit causes the appropriate status bit to be set. Exceeding either
limit can also generate SMBALERT interrupts.
Channel
Voltage Channels
Remote Temperature
Local Temperature
Measurement Time
11 ms
39 ms
12 ms
Reg. 0x4E, Remote 1 temperature low limit = 0x01 default
Reg. 0x4F, Remote 1 temperature high limit = 0x7F default
Reg. 0x50, local temperature low limit = 0x01 default
Reg. 0x51, local temperature high limit = 0x7F default
Reg. 0x52, Remote 2 temperature low limit = 0x01 default
Reg. 0x53, Remote 2 temperature high limit = 0x7F default
Reading Temperature from the ADT7468
It is important to note that temperature can be read from the
Single-Channel ADC Conversions
Setting Bit 6 of Configuration Register 2 (Reg. 0x73) places
the ADT7468 into single-channel ADC conversion mode. In
this mode, the ADT7468 can be made to read a single temp-
erature channel only. The appropriate ADC channel is selected
by writing to Bits <7:5> of the TACH1 minimum high byte
register (0x55).
Table 11. Channel Selection
ADT7468 as an 8-bit value (with 1°C resolution) or as a 10-bit
value (with 0.25°C resolution). If only 1°C resolution is
required, the temperature readings can be read back at any
time and in no particular order.
Bits <7:5> Reg. 0x55
101
110
111
Channel Selected
Remote 1 temperature
Local temperature
Remote 2 temperature
If the 10-bit measurement is required, this involves a 2-register
read for each measurement. The extended resolution register
(Reg. 0x77) should be read first. This causes all temperature
reading registers to be frozen until all temperature reading
registers have been read from. This prevents an MSB reading
from being updated while its two LSBs are being read and
vice versa.
ADDITIONAL ADC FUNCTIONS FOR
TEMPERATURE MEASUREMENT
A number of other functions are available on the ADT7468 to
offer the system designer increased flexibility.
Turn-Off Averaging
For each temperature measurement read from a value register,
16 readings are made internally and the results are averaged
before being placed into the value register. Sometimes it is
necessary to take a very fast measurement. Setting Bit 4 of
Configuration Register 2 (Reg. 0x73) turns averaging off.
Table 9. Conversion Time with Averaging Disabled
Channel Measurement Time
Voltage Channels 0.7 ms
Configuration Register 2 (Reg. 0x73)
<4> = 1, averaging off.
<6> = 1, single-channel convert mode.
TACH1 Minimum High Byte (Reg. 0x55)
<7:5> selects ADC channel for single-channel convert mode.
Overtemperature Events
Overtemperature events on any of the temperature channels can
be detected and dealt with automatically in automatic fan speed
control mode. Register 0x6A to Register 0x6C are the THERM
temperature limits. When a temperature exceeds its THERM
temperature limit, all PWM outputs run at the maximum PWM
duty cycle (Reg. 0x38, Reg. 0x39, and Reg. 0x3A). This
effectively runs the fans at the fastest allowed speed. The fans
stay running at this speed until the temperature drops below
THERM minus hysteresis. (This can be disabled by setting the
boost bit in Configuration Register 3, Bit 2, Reg. 0x78.) The
hysteresis value for that THERM temperature limit is the value
programmed into Reg. 0x6D and Reg. 0x6E (hysteresis
registers). The default hysteresis value is 4°C.
Remote Temperature 1
7 ms
Remote Temperature 2
Local Temperature
7 ms
1.3 ms
THERM LIMIT
HYSTERESIS (°C)
TEMPERATURE
100%
FANS
Figure 27. THERM Temperature Limit Operation
Rev. 3 | Page 21 of 81 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7473ZEVB | BOARD EVALUATION FOR ADT7473 |
| ADT7475EBZEVB | BOARD EVALUATION FOR ADT7475 |
| ADT7476EBZEVB | BOARD EVALUATION FOR ADT7476 |
| ADT7490ZEVB | BOARD EVALUATION FOR ADT7490 |
| ADZS-21262-1-EZEXT | BOARD DAUGHTER FOR ADSP-21262 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7470 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470ARQ | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP |
| ADT7470ARQ-REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADT7470ARQ-REEL7 | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP T/R |
发布紧急采购，3分钟左右您将得到回复。