参数资料
| 型号： | ADT7468ZEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/81页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADT7468 |
| 标准包装： | 1 |
| 其它名称： | EVAL-ADT7468EB EVAL-ADT7468EB-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页
ADT7468
For applications where the monitoring cycle time is important,
it can be calculated easily.
The measured channels are
Bit 6 (R2T) = 1, Remote 2 temperature high or low limit has
been exceeded.
Bit 5 (LT) = 1, local temperature high or low limit has been
?
?
?
?
Four dedicated supply voltage inputs
Supply voltage (V CC pin)
Local temperature
Two remote temperatures
exceeded.
Bit 4 (R1T) = 1, Remote 1 temperature high or low limit has
been exceeded.
Bit 3 (5 V) = 1, 5 V high or low limit has been exceeded.
Bit 2 (V CC ) = 1, V CC high or low limit has been exceeded.
As mentioned previously, the ADC performs round-robin
conversions and takes 11 ms for each voltage measurement,
12 ms for a local temperature reading, and 39 ms for each
remote temperature reading. The total monitoring cycle time
for averaged voltage and temperature monitoring is, therefore,
nominally
(5 × 11) + 12 + (2 × 39) = 145 ms
Fan TACH measurements are made in parallel and are not
synchronized with the analog measurements in any way.
STATUS REGISTERS
The results of limit comparisons are stored in Status Registers 1
and 2. The status register bit for each channel reflects the status
of the last measurement and limit comparison on that channel.
If a measurement is within limits, the corresponding status
register bit is cleared to 0. If the measurement is out-of-limit,
the corresponding status register bit is set to 1.
The state of the various measurement channels can be polled by
reading the status registers over the serial bus. In Bit 7 (OOL) of
Status Register 1 (Reg. 0x41), 1 means that an out-of-limit event
has been flagged in Status Register 2. This means that the user
also needs to read Status Register 2. Alternatively, Pin 10 or
Pin 14 can be configured as an SMBALERT output. This hard
interrupt automatically notifies the system supervisor of an out-
of-limit condition. Reading the status registers clears the appro-
priate status bit as long as the error condition that caused the
interrupt has cleared. Status register bits are sticky. The status
bits are referred to as sticky, because they remain set until read
by software. Whenever a status bit is set, indicating an out-of-
limit condition, it remains set even if the event that caused it
has ceased (until read). The only way to clear the status bit is to
read the status register after the event has ceased. Interrupt
status mask registers (0x74, and 0x75) allow individual inter-
Bit 1 (V CCP ) = 1, V CCP high or low limit has been exceeded.
Bit 0 (2.5 V) = 1, 2.5 V high or low limit has been exceeded.
Status Register 2 (Reg. 0x42)
Bit 7 (D2) = 1, indicates an open or short on D2+/D2– inputs.
Bit 6 (D1) = 1, indicates an open or short on D1+/D1– inputs.
Bit 5 (F4P) = 1, indicates Fan 4 has dropped below minimum
speed. Alternatively, indicates that the THERM limit has been
exceeded, if the THERM function is used.
Bit 4 (FAN3) = 1, indicates Fan 3 has dropped below minimum
speed.
Bit 3 (FAN2) = 1, indicates Fan 2 has dropped below minimum
speed.
Bit 2 (FAN1) = 1, indicates Fan 1 has dropped below minimum
speed.
Bit 1 (OVT) = 1, indicates a THERM overtemperature limit has
been exceeded.
Bit 0 (12V/VC) = 1, indicates a 12 V high or low limit has been
exceeded. If the VID code change function is used, this bit
indicates a change in VID code on the VID0 to VID5 inputs.
INTERRUPTS
SMBALERT Interrupt Behavior
The ADT7468 can be polled for status, or an SMBALERT
interrupt can be generated for out-of-limit conditions. It is
important to note how the SMBALERT output and status bits
behave when writing interrupt handler software.
HIGH LIMIT
TEMPERATURE
CLEARED ON READ
rupt sources to be masked from causing an SMBALERT. How-
ever, if one of these masked interrupt sources goes out-of-limit,
its associated status bit is set in the interrupt status registers.
Status Register 1 (Reg. 0x41)
Bit 7 (OOL) = 1, denotes a bit in Status Register 2 is set and
“STICKY”
STATUS BIT
SMBALERT
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
(TEMP BELOW LIMIT)
Status Register 2 should be read.
Rev. 3 | Page 23 of 81 | www.onsemi.com
Figure 28. SMBALERT and Status Bit Behavior
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7473ZEVB | BOARD EVALUATION FOR ADT7473 |
| ADT7475EBZEVB | BOARD EVALUATION FOR ADT7475 |
| ADT7476EBZEVB | BOARD EVALUATION FOR ADT7476 |
| ADT7490ZEVB | BOARD EVALUATION FOR ADT7490 |
| ADZS-21262-1-EZEXT | BOARD DAUGHTER FOR ADSP-21262 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7470 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470ARQ | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP |
| ADT7470ARQ-REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADT7470ARQ-REEL7 | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP T/R |
发布紧急采购，3分钟左右您将得到回复。