参数资料
| 型号： | ADT7468ZEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 28/81页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADT7468 |
| 标准包装： | 1 |
| 其它名称： | EVAL-ADT7468EB EVAL-ADT7468EB-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页
ADT7468
ACTIVE COOLING
DRIVING THE FAN USING PWM CONTROL
The ADT7468 uses pulse-width modulation (PWM) to control
fan speed. This relies on varying the duty cycle (or on/off ratio)
of a square wave applied to the fan to vary the fan speed. The
external circuitry required to drive a fan using PWM control is
extremely simple. For 4-wire fans, the PWM drive might need
only a pull-up resistor. In many cases, the 4-wire fan PWM
input has a built-in pull-up resistor.
The ADT7468 PWM frequency can be set to a selection of low
frequencies or a single high PWM frequency. The low fre-
quency options are usually used for 2-wire and 3-wire fans,
while the high frequency option is usually used with 4-wire
fans.
For 2-wire or 3-wire fans, a single N-channel MOSFET is the
only drive device required. The specifications of the MOSFET
depend on the maximum current required by the fan being
driven and the input capacitance of the FET. Because a 10 k?
(or greater) resistor must be used as a PWM pull-up, an FET
Figure 34. Driving a 3-Wire Fan Using an N-Channel MOSFET
Figure 34 uses a 10 k? pull-up resistor for the TACH signal.
This assumes that the TACH signal is an open-collector from
the fan. In all cases, the TACH signal from the fan must be kept
below 5 V maximum to prevent damaging the ADT7468. If in
doubt as to whether the fan has an open-collector or totem-pole
TACH output, use one of the input signal conditioning circuits
shown in the Fan Speed Measurement section.
Figure 35 shows a fan drive circuit using an NPN transistor,
such as a general-purpose MMBT2222. While these devices are
inexpensive, they tend to have much lower current handling
capabilities and higher on resistance than MOSFETs. When
choosing a transistor, care should be taken to ensure that it
meets the fan’s current requirements. Ensure that the base
resistor is chosen such that the transistor is saturated when the
fan is powered on.
Because 4-wire fans are powered continuously, the fan speed is
not switched on or off as with previous PWM driven/powered
fans. This enables it to perform better than 3-wire fans,
especially for high frequency applications.
with large input capacitance can cause the PWM output to
become distorted and adversely affect the fan control range.
This is a requirement only when using high frequency
12V
10k ?
12V
PWM mode.
Typical notebook fans draw a nominal 170 mA, and so SOT
TACH
10k ?
4.7k ?
3.3V
TACH
12V
FAN
1N4148
devices can be used where board space is a concern. In
desktops, fans can typically draw 250 mA to 300 mA each. If
ADT7468
665 ?
you drive several fans in parallel from a single PWM output or
drive larger server fans, the MOSFET must handle the higher
current requirements. The only other stipulation is that the
PWM
Q1
MMBT2222
MOSFET should have a gate voltage drive, V GS < 3.3 V, for direct
interfacing to the PWM_OUT pin. V GS can be greater than 3.3 V
as long as the pull-up on the gate is tied to 5 V. The MOSFET
should also have a low on resistance to ensure that there is not
significant voltage drop across the FET, which would reduce the
voltage applied across the fan and, therefore, the maximum
Figure 35. Driving a 3-Wire Fan Using an NPN Transistor
Figure 36 shows a typical drive circuit for 4-wire fans.
12V 12V
12V, 4-WIRE FAN
4.7k ?
operating speed of the fan.
Figure 34 shows how to drive a 3-wire fan using PWM control.
TACH/AIN
10k ?
10k ?
TACH
V CC
TACH
PWM
12V
10k ?
12V
ADT7468
3.3V
2k ?
TACH/AIN
10k ?
4.7k ?
12V
FAN
1N4148
PWM
3.3V
ADT7468
PWM
10k ?
Q1
NDT3055L
Rev. 3 | Page 28 of 81 | www.onsemi.com
Figure 36. Driving a 4-Wire Fan
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7473ZEVB | BOARD EVALUATION FOR ADT7473 |
| ADT7475EBZEVB | BOARD EVALUATION FOR ADT7475 |
| ADT7476EBZEVB | BOARD EVALUATION FOR ADT7476 |
| ADT7490ZEVB | BOARD EVALUATION FOR ADT7490 |
| ADZS-21262-1-EZEXT | BOARD DAUGHTER FOR ADSP-21262 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7470 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller |
| ADT7470ARQ | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP |
| ADT7470ARQ-REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADT7470ARQ-REEL7 | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP T/R |
发布紧急采购，3分钟左右您将得到回复。