参数资料
| 型号： | KIT13892VLEVBEJ |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 108/158页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC13892 |
| 标准包装： | 1 |
| 主要目的： | 电源管理和用户界面 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC13892 |
| 主要属性： | 10 位 ADC，4 输出降压转换器，12 LDO |
| 次要属性： | 与 i.MX51、i.MX37、i.MX35、i.MX27 一起使用 |
| 已供物品： | 板，线缆，文档 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页当前第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
ADC SUBSYSTEM
Figure 30 shows how the ATO and ATOX settings determine the readout sequence. The ATO should be set long enough so
that the touch screen can be biased properly before conversions start.
Touchscreen Readout for ATOX=0
1/32K
Trigger
ATO+1
Conversions
0, 1, 2
ATO+1
Conversions
3, 4, 5
ATO+1
Conversions
6, 7
Touchscreen
Polarization
End of Conversi on 2
New Touchscreen
Polarization
End of Conversion 5
New Touchscreen
Polarization
End of Conversion 7
Touchscreen
De-Polarization
Touchscreen Readout for ATOX=1
1/32K
ATO+1
ATO+1
ATO+1
ATO+1
Etc.
Trigger
Conversion 0
Conversion 1
Conversion 2
Conversion 3
Touchscreen
Polarization
End of Conversion 2
New Touchscreen
Pol arization
Figure 30. Touch Screen Reading Timing
The main resistive touch screen panel characteristics are listed in Table 5 . The switch matrix and readout scheme is designed
such that the on chip switch resistances are of no influence on the overall readout. The readout scheme however does not
account for contact resistances as present in the touch screen connectors. Therefore, the touch screen readings will have to be
calibrated by the user or in the factory where one has to point with a stylus the opposite corners of the screen.
When reading out the X-coordinate, the 10-bit ADC reading represents a 10-bit coordinate with '0' for a coordinate equal to
TSX2, and full scale '1023' when equal to TSX1. When reading out the Y-coordinate, the 10-bit ADC reading represents a 10-bit
coordinate with '0' for a coordinate equal to TSY2, and full scale '1023' when equal to TSY1. When reading the contact resistance
the 10-bit ADC reading represents the voltage drop over the contact resistance created by the known current source multiplied
by two.
Table 97. Touchscreen Interface Characteristics
Parameter
Interrupt Threshold for Pressure Application
Interrupt Threshold for Pressure Removal
Current Source Inaccuracy
Condition
Over-temperature
Min
40
60
–
Typ
50
80
–
Max
60
95
20
Unit
kOhm
kOhm
%
The reference for the touch screen is TSREF and is powered from VCORE. In touch screen operation, TSREF is a dedicated
regulator. No other loads than the touch screen should be connected here. When the ADC performs non touch screen
conversions, the ADC does not rely on TSREF and the reference can be disabled. In applications not supporting touch screen
at all, the TSREF can be used as a low current general purpose regulator, or it can be kept disabled and the bypass capacitor
omitted. The operating mode of TSREF can be controlled with the TSREFEN bit in the same way as some other general purpose
COULOMB COUNTER
As indicated earlier on in this Section, the current into and from the battery can be read out through the general purpose ADC
as a voltage drop over the R1 sense resistor. Together with battery voltage reading, the battery capacity can be estimated. A
more accurate battery capacity estimation can be obtained by using the integrated Coulomb Counter.
The Coulomb Counter (or CC) monitors the current flowing in/out of the battery by integrating the voltage drop across the
battery current sense resistor R1, followed by an A to D conversion. The result of the A to D conversion is used to increase/
decrease the contents of a counter that can be read out by software. This function will require a 10 μ F output capacitor to perform
MC13892
Analog Integrated Circuit Device Data
108
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| KIT17C724EPEVBE | KIT FOR 17C7242CH HBRIDGE PWR IC |
| KIT33810EKEVME | BOARD EVAL FOR MC33810 |
| KIT33811EGEVBE | KIT EVAL 33811 SOLENOID MON IC |
| KIT33812ECUEVME | KIT DESIGN FOR 33812/S12P |
| KIT33812EKEVBE | BOARD EVALUATION FOR MC33812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT-1395 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| Kit-1395G1 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G10 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G2 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G3 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
发布紧急采购，3分钟左右您将得到回复。