参数资料
| 型号： | KIT13892VLEVBEJ |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 50/158页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC13892 |
| 标准包装： | 1 |
| 主要目的： | 电源管理和用户界面 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC13892 |
| 主要属性： | 10 位 ADC，4 输出降压转换器，12 LDO |
| 次要属性： | 与 i.MX51、i.MX37、i.MX35、i.MX27 一起使用 |
| 已供物品： | 板，线缆，文档 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
CLOCK GENERATION AND REAL TIME CLOCK
Table 16. Crystal Oscillator Main Characteristics
Parameter
Operating Voltage
Coin cell Disconnect Threshold
RTC oscillator startup time
XTAL1 Input Level
XTAL1 Input Range
Output Low CLK32K,
CLK32KMCU
Output High
Condition
Oscillator and RTC Block from BP
At LICELL
Upon application of power
External clock source
External clock source
Output sink 100 μ A
CLK32K Output source 100 μ A
CLK32KMCU Output source 100 μ A
Min
1.2
1.8
-
0.3
-0.5
0
SPIVCC-0.2
VSRTC-0.2
Typ
–
–
–
–
–
–
–
–
Max
4.65
2.0
1.0
-
1.2
0.2
SPIVCC
VSRTC
Units
V
V
sec
V PP
V
V
V
V
CL=50 pF
CLK32KDRV[1:0] = 00 (default)
–
22
–
ns
CLK32K Rise and Fall Time
CLD32KMCU Rise and Fall Time
CLK32K and CLK32KMCU
Output Duty Cycle
CLK32KDRV[1:0] = 01
CLK32KDRV[1:0] = 10
CLK32KDRV[1:0] = 11
CL=12 pF
Crystal on XTAL1, XTAL2 pins
–
–
–
–
45
11
High Z
44
22
–
–
–
–
–
55
ns
ns
ns
ns
%
OSCILLATOR APPLICATION GUIDELINES
The guidelines below may prove to be helpful in providing a crystal oscillator that starts reliably and runs with minimal jitter.
PCB leakage: The RTC amplifier is a low-current circuit. Therefore, PCB leakage may significantly change the operating point
of the amplifier and even the drive level to the crystal. (Changing the drive level to the crystal may change the aging rate, jitter,
and even the frequency at a given load capacitance.) The traces should be kept as short as possible to minimize the leakage,
and good PCB manufacturing processes should be maintained.
Layout: The traces from the MC13892 to the crystal, load capacitance, and the RTC Ground are sensitive. They must be kept
as short as possible with minimal coupling to other signals. The signal ground for the RTC is to be connected to GNDRTC, and
via a single connection, GNDRTC to the system ground. The CLK32K and CLK32KMCU square wave outputs must be kept away
from the crystal / load capacitor leads, as the sharp edges can couple into the circuit and lead to excessive jitter. The crystal /
load capacitance leads and the RTC Ground must form a minimal loop area.
Crystal Choice: Generally speaking, crystals are not interchangeable between manufacturers, or even different packages for
a given manufacturer. If a different crystal is considered, it must be fully characterized with the MC13892 before it can be
considered.
Tuning Capacitors: The nominal load capacitance is 9.0 pF, therefore the total capacitance at each node should be 18 pF,
composed out of the load capacitance, the effective input capacitance at each pin, plus the PCB stray capacitance for each pin.
SRTC SUPPORT
The MC13892 provides support for processors which have an integrated SRTC for Digital Rights Management (DRM), by
providing a VSRTC voltage to bias the SRTC module of the processor, as well as a CLK32KMCU at the VSRTC output level.
When configured for DRM mode (SPI bit DRM = 1), the CLK32MCU driver will be kept enabled through all operational states,
to ensure that the SRTC module always has its reference clock. If DRM = 0, the CLK32KMCU driver will not be maintained in the
Off state. Refer to Table 23 for the operating behavior of the CLK32KMCU output in User Off, Memory Hold, User off Wait, and
internal MEMHOLD PCUT modes.
It is also necessary to provide a means for the processor to do an RTC initiated wake-up of the system, if it has been
programmed for such capability. This can be accomplished by connecting an open drain NMOS driver to the PWRON pin of the
MC13892, so that it is in effect a parallel path for the power key. The MC13892 will not be able to discern the turn on event from
a normal power key initiated turn on, but the processor should have the knowledge, since the RTC initiated turn on is generated
locally.
MC13892
Analog Integrated Circuit Device Data
50
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| KIT17C724EPEVBE | KIT FOR 17C7242CH HBRIDGE PWR IC |
| KIT33810EKEVME | BOARD EVAL FOR MC33810 |
| KIT33811EGEVBE | KIT EVAL 33811 SOLENOID MON IC |
| KIT33812ECUEVME | KIT DESIGN FOR 33812/S12P |
| KIT33812EKEVBE | BOARD EVALUATION FOR MC33812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT-1395 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| Kit-1395G1 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G10 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G2 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G3 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
发布紧急采购，3分钟左右您将得到回复。