参数资料
| 型号： | KIT13892VLEVBEJ |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 86/158页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC13892 |
| 标准包装： | 1 |
| 主要目的： | 电源管理和用户界面 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC13892 |
| 主要属性： | 10 位 ADC，4 输出降压转换器，12 LDO |
| 次要属性： | 与 i.MX51、i.MX37、i.MX35、i.MX27 一起使用 |
| 已供物品： | 板，线缆，文档 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页当前第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
SUPPLIES
PERIPHERAL INTERFACING
IC interfaces in the lineups generally fall in two categories: low voltage IO primarily associated with the AP IC and certain
peripherals at SPIVCC level (powered from SW4), and a higher voltage interface level associated with other peripherals not
compatible with the 1.8 V SPIVCC. VIOHI is provided at a fixed 2.775 V level for such interfaces, and may also be applied to
other system needs within the guidelines of the regulator specifications. The input VINIOHI is not only used by the VIOHI
regulator, but also by other blocks, therefore it should always be connected to BP, even if the VIOHI regulator is not used by the
system.
VIOHI has an internal PMOS pass FET which will support loads up to 100 mA.
CAMERA
The camera module is supplied by the regulator VCAM. This allows powering the entire module independent of the rest of
other parts of the system, as well as to select from a number of VCAM output levels for camera vendor flexibility. In applications
with a dual camera, it is anticipated that only one of the two cameras is active at a time, allowing the VCAM supply to be shared
between them.
VCAM has an internal PMOS pass FET which will support up to 2.0 Mpixel Camera modules (<65 mA). To support higher
resolution cameras, an external PNP is provided. The external PNP configuration is offered to avoid excess on-chip power
dissipation at high loads, and large differential between BP and output settings. For lower current requirements, an integrated
PMOS pass FET is included. The input pin for the integrated PMOS option is shared with the base current drive pin for the PNP
option. The external PNP configuration must be committed as a hardwired board level implementation, while the operating mode
is selected through the VCAMCONFIG bit after startup. The VCAM is not automatically enabled during the power up sequence,
allowing software to properly set the VCAMCONFIG bit before the regulator is activated. The recommended PNP device is the
ON Semiconductor NSS12100XV6T1G which is capable of handling up to 250 mW of continuous dissipation at a minimum
footprint and 75 °C of ambient. For use cases where up to 500 mW of dissipation is required, the recommended PNP device is
the ON Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required.
The input VINCAM should always be connected to BP, even if the VCAM regulator is not used by the system.
Table 56. VCAM Voltage Control
ILoad max
Parameter
VCAM[1:0]
Value
00
01
10
11
Output Voltage
2.5 V
2.6 V
2.75 V
3.00 V
VCAMCONFIG=0
Internal Pass FET
65 mA
65 mA
65 mA
65 mA
VCAMCONFIG=1
External PNP
250 mA
250 mA
250 mA
250 mA
MULTI-MEDIA CARD SUPPLY
This supply domain is generally intended for user accessible multi-media cards, such as Micro-SD (TransFlash), RS-MMC,
and the like. An external PNP is utilized for this LDO to avoid excess on-chip power dissipation at high loads and large differential
between BP and output settings. The external PNP device is always connected to the BP line in the application. VSD may also
be applied to other system needs within the guidelines of the regulator specifications. The recommended PNP device is the ON
Semiconductor NSS12100XV6T1G, which is capable of handling up to 250 mW of continuous dissipation at a minimum footprint
and 75 °C of ambient. For use cases where up to 500 mW of dissipation is required, the recommended PNP device is the ON
Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required. At the 1.8 V set point, the
VSD regulator can be powered from an external buck regulator (2.2 V typ) for an efficiency advantage and reduced power
dissipation in the pass devices.
MC13892
Analog Integrated Circuit Device Data
86
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| KIT17C724EPEVBE | KIT FOR 17C7242CH HBRIDGE PWR IC |
| KIT33810EKEVME | BOARD EVAL FOR MC33810 |
| KIT33811EGEVBE | KIT EVAL 33811 SOLENOID MON IC |
| KIT33812ECUEVME | KIT DESIGN FOR 33812/S12P |
| KIT33812EKEVBE | BOARD EVALUATION FOR MC33812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT-1395 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| Kit-1395G1 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G10 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G2 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G3 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
发布紧急采购，3分钟左右您将得到回复。