参数资料
型号: KIT13892VLEVBEJ
厂商: Freescale Semiconductor
文件页数: 65/158页
文件大小: 0K
描述: KIT EVAL FOR MC13892
标准包装: 1
主要目的: 电源管理和用户界面
嵌入式:
已用 IC / 零件: MC13892
主要属性: 10 位 ADC,4 输出降压转换器,12 LDO
次要属性: 与 i.MX51、i.MX37、i.MX35、i.MX27 一起使用
已供物品: 板,线缆,文档
FUNCTIONAL DEVICE OPERATION
OPERATING MODES
Table 30. Standby Pin and Polarity Control
STANDBY (Pin)
0
1
1
STANDBYINV (SPI bit)
1
0
0
STANDBYSEC (Pin)
1
0
1
STANDBYSECINV (SPI bit)
0
1
0
STANDBY Control (58)
1
1
1
Notes
58. STANDBY = 0: System is not in Standby; STANDBY = 1: System is in Standby and Standby programmability is activated.
When requesting standby, a programmable delay (STBYDLY) of 0 to 3 clock cycles of the 32 kHz clock is applied before
actually going into standby (i.e. before turning off some supplies). No delay is applied when coming out of standby.
Table 31. Delay of STANDBY- Initiated Response
STBYDLY[1:0]
00
01
10
11
Function (1)
No Delay
One 32 K period (default)
Two 32 K periods
Three 32 K periods
REGULATOR MODE CONTROL
The regulators with embedded pass devices (VDIG, VPLL, VIOHI, VUSB, VUSB2, and VAUDIO) have an adaptive biasing
scheme, thus, there are no distinct operating modes such as a Normal mode and a Low-power mode. Therefore, no specific
control is required to put these regulators in a Low-power mode.
The regulators with external pass devices (VSD, VVIDEO, VGEN1, and VGEN2) can also operate in a Normal and Low-power
mode. However, since a load current detection cannot be performed for these regulators, the transition between both modes is
not automatic and is controlled by setting the corresponding mode bits for the operational behavior desired.
The regulators VGEN3 and VCAM can be configured for using the internal pass device or external pass device as explained
in Power Control System . For both configurations, the transition between Normal and Low-power modes is controlled by setting
the VxMODE bit for the specific regulator. Therefore, depending on the configuration selected, the automatic Low-power mode
is available.
The regulators can be disabled and the general purpose outputs can be forced low when going into Standby as described
previously. Each regulator and GPO has an associated SPI bit for this. When the bit is not set, STANDBY is of no influence. The
actual operating mode of the regulators as a function of STANDBY is not reflected through the SPI. In other words, the SPI will
read back what is programmed, not the actual state.
Table 32. LDO Regulator Control (External Pass Device LDOs)
VxEN
0
1
1
1
1
1
VxMODE
X
0
1
X
0
1
VxSTBY
X
0
0
1
1
1
STANDBY
X
X
X
0
1
1
Regulator Vx
Off
On
Low-power
On
Off
Low-power
Notes
59. This table is valid for regulators with an external pass device
60. STANDBY refers to a Standby event as described earlier
For regulators with internal pass devices and general outputs, the previous table can be simplified.
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
65
相关PDF资料
PDF描述
KIT17C724EPEVBE KIT FOR 17C7242CH HBRIDGE PWR IC
KIT33810EKEVME BOARD EVAL FOR MC33810
KIT33811EGEVBE KIT EVAL 33811 SOLENOID MON IC
KIT33812ECUEVME KIT DESIGN FOR 33812/S12P
KIT33812EKEVBE BOARD EVALUATION FOR MC33812
相关代理商/技术参数
参数描述
KIT-1395 制造商:Anderson Power Products (APP) 功能描述:KIT
Kit-1395G1 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT
Kit-1395G10 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT
Kit-1395G2 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT
Kit-1395G3 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT