参数资料
| 型号： | KIT13892VLEVBEJ |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 123/158页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MC13892 |
| 标准包装： | 1 |
| 主要目的： | 电源管理和用户界面 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC13892 |
| 主要属性： | 10 位 ADC，4 输出降压转换器，12 LDO |
| 次要属性： | 与 i.MX51、i.MX37、i.MX35、i.MX27 一起使用 |
| 已供物品： | 板，线缆，文档 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页当前第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
SPI BITMAP
The 24 bit wide registers are numbered from 0 to 63, and are referenced throughout this document by register number, or
representative name as given in the corresponding captions. The contents of all registers are given in the tables defined in this
chapter; each table includes the following information:
Name: Name of the bit. Spare bits are implemented in the design for future use, but are not assigned. Unused bits are not
available in the design. Reserved bits are not implemented in the design, but are used on other PMICs.
Bit #: The bit location in the register (0-23)
R/W: Read / Write access and control
? R is read access
? W is write access
? R/W is read and write access
? RW1C is read and write access with write 1 to clear
? RWM is read and write access while the device can modify the bit
Reset: Resetting signal
? RESETB, which is the same signal as the RESETB pin (so bit is held in reset as long as RESETB is low)
? RTCPORB which is the reset signal of the RTC module (so bit is no longer held in reset once RTC power is good)
? OFFB which is an internal signal generated when transitioning into the Off state
? NONE. There is no reset signal for hardwired bits nor for the bits of which the state is determined by the power up mode
settings
Default: The value after reset as noted in the Default column of the SPI map.
? Fixed defaults are explicitly declared as 0 or 1.
? * corresponds to Read / Write bits that are initialized at startup based on power up mode settings (board level pin
connections) validated at the beginning of Cold or Warm Start. Bits are subsequently SPI modifiable.
? S corresponds to Read only sense bits that continuously monitor an input signal (sense signal is not latched).
? L corresponds to Read only sense bits that are latched at startup.
? X indicates that the state does not have an explicitly defined default value which can be specified. For instance, some bits
default to a value which is dependent on the version of the IC.
Description: A short description of the bit function, in some cases additional information is included
The following tables are intended to give a summarized overview, for details on the bit description, see the individual chapters.
Table 112. Register 0, Interrupt Status 0
Name
ADCDONEI
ADCBISDONEI
TSI
VBUSVALIDI
IDFACTORYI
USBOVI
CHGDETI
CHGFAULTI
CHGREVI
CHGSHORTI
CCCVI
CHGCURRI
BPONI
LOBATLI
LOBATHI
Reserved
BVALIDI
Reserved
Reserved
IDFLOATI
IDGNDI
Bit #
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
R/W
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
RW1C
R
RW1C
R
R
RW1C
RW1C
Reset
RESETB
RESETB
RESETB
OFFB
RESETB
RTCPORB
OFFB
RTCPORB
RESETB
RESETB
RESETB
RESETB
OFFB
RESETB
RESETB
OFFB
RESETB
RESETB
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Description
ADC has finished requested conversions
ADCBIS has finished requested conversions
Touch screen wake-up
VBUSVALID detect
ID factory mode detect
USB over-voltage detection
Charger attach
Charger fault detection
Charger path reverse current
Charger path short circuit
Charger path CC / CV transition detect
Charge current below threshold warning
BP turn on threshold
Low battery low threshold warning
Low battery high threshold warning
For future use
USB B-session valid interrupt
For future use
For future use
USB ID float detect
USB ID ground detect
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
123
相关PDF资料 |
PDF描述 |
|---|---|
| KIT17C724EPEVBE | KIT FOR 17C7242CH HBRIDGE PWR IC |
| KIT33810EKEVME | BOARD EVAL FOR MC33810 |
| KIT33811EGEVBE | KIT EVAL 33811 SOLENOID MON IC |
| KIT33812ECUEVME | KIT DESIGN FOR 33812/S12P |
| KIT33812EKEVBE | BOARD EVALUATION FOR MC33812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT-1395 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| Kit-1395G1 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G10 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G2 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
| Kit-1395G3 | 制造商:ANDERSON POWER PRODUCTS 功能描述:KIT |
发布紧急采购，3分钟左右您将得到回复。