参数资料
型号: S29WS128J0PBFW002
厂商: SPANSION LLC
元件分类: PROM
英文描述: 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84
封装: 8 X 11.60 MM, LEAD FREE, FBGA-84
文件页数: 61/97页
文件大小: 2421K
代理商: S29WS128J0PBFW002
64
S29WS128J/064J
S29WS-J_00_A6 May 11, 2006
Dat a
S h ee t
If the output is low (Busy), the device is actively erasing or programming. (This includes program-
ming in the Erase Suspend mode.) If the output is in high impedance (Ready), the device is in
the read mode, the standby mode, or in the erase-suspend-read mode. Table 20, “Write Opera-
tion Status,” on page 67 shows the outputs for RDY.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or
complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read
at any address in the same bank, and is valid after the rising edge of the final WE# pulse in the
command sequence (prior to the program or erase operation), and during the sector erase time-
out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any ad-
dress cause DQ6 to toggle. When the operation is complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6
toggles for approximately 100 s, then returns to reading array data. If not all selected sectors
are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the
selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or
is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm
is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops tog-
gling. However, the system must also use DQ2 to determine which sectors are erasing or erase-
suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 ms after the
program command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embed-
ded Program algorithm is complete.
See the following for additional information: Figure 8, “Toggle Bit Algorithm,” on page 65, DQ6:
Toggle Bit I on DQ6 requires either OE# or CE# to be deasserteed and reasserted to show the
change in state.
相关PDF资料
PDF描述
S29WS128J0PBAW002 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84
S2M 2 A, 1000 V, SILICON, RECTIFIER DIODE, DO-214AA
S2R72A44F12C4 UNIVERSAL SERIAL BUS CONTROLLER, PQFP48
S2V20-4000 1.7 A, 200 V, SILICON, RECTIFIER DIODE
S2V60-4070 1.7 A, SILICON, RECTIFIER DIODE
相关代理商/技术参数
参数描述
S29WS128J0PBFW01 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
S29WS128J0PBFW10 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
S29WS128J0PBFW11 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
S29WS128N 制造商:SPANSION 制造商全称:SPANSION 功能描述:256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
S29WS128N0LBAI010 制造商:SPANSION 制造商全称:SPANSION 功能描述:256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY