- 您现在的位置：买卖IC网 > PDF目录297338 > S29WS128J0PBFW002 (SPANSION LLC) 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84 PDF资料下载
参数资料
| 型号： | S29WS128J0PBFW002 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84 |
| 封装： | 8 X 11.60 MM, LEAD FREE, FBGA-84 |
| 文件页数： | 9/97页 |
| 文件大小： | 2421K |
| 代理商： | S29WS128J0PBFW002 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
May 11, 2006 S29WS-J_00_A6
S29WS128J/064J
17
D a ta
Sh eet
An erase operation can erase one sector, multiple sectors, or the entire device. Table 12, “WS128J
dicate the address space that each sector occupies. The device address space is divided into four
banks. A “bank address” is the address bits required to uniquely select a bank. Similarly, a “sector
address” is the address bits required to uniquely select a sector.
the write mode. The AC Characteristics section contains timing specification tables and timing di-
agrams for write operations.
Accelerated Program Operation
The device offers accelerated program operations through the ACC function. ACC is primarily in-
tended to allow faster manufacturing throughput at the factory.
If the system asserts VHH on this input, the device automatically enters the aforementioned Un-
lock Bypass mode and uses the higher voltage on the input to reduce the time required for
program operations. The system would use a two-cycle program command sequence as required
by the Unlock Bypass mode. Removing VHH from the ACC input returns the device to normal op-
eration. Note that sectors must be unlocked prior to raising ACC to VHH. Note that the ACC pin
must not be at VHH for operations other than accelerated programming, or device damage may
result. In addition, the ACC pin must not be left floating or unconnected; inconsistent behavior of
the device may result.
When at VIL, ACC locks all sectors. ACC should be at VIH for all other conditions.
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector protection ver-
ification, through identifier codes output from the internal register (which is separate from the
memory array) on DQ15–DQ0. This mode is primarily intended for programming equipment to
automatically match a device to be programmed with its corresponding programming algorithm.
However, the autoselect codes can also be accessed in-system through the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Ad-
dress pins must be as shown in Table 3, “Autoselect Codes (High Voltage Method),” on page 18.
In addition, when verifying sector protection, the sector address must appear on the appropriate
the remaining address bits that are don’t care. When all necessary bits have been set as re-
quired, the programming equipment may then read the corresponding identifier code on DQ15–
DQ0. However, the autoselect codes can also be accessed in-system through the command reg-
ister, for instances when the device is erased or programmed in a system without access to high
voltage on the A9 pin. The command sequence is illustrated in Table 18, “Command Definitions,”
on page 60. Note that if a Bank Address (BA) on address bits A22, A21, and A20 for the WS128J
(A21:A19 for the WS064J) is asserted during the third write cycle of the autoselect command,
the host system can read autoselect data that bank and then immediately read array data from
the other bank, without exiting the autoselect mode.
To access the autoselect codes in-system, the host system can issue the autoselect command
via the command register, as shown in Table 18, “Command Definitions,” on page 60. This
method does not require VID. Autoselect mode may only be entered and used when in the asyn-
chronous read mode. Refer to the “Autoselect Command Sequence” section on page 51 for more
information.
相关PDF资料 |
PDF描述 |
|---|---|
| S29WS128J0PBAW002 | 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84 |
| S2M | 2 A, 1000 V, SILICON, RECTIFIER DIODE, DO-214AA |
| S2R72A44F12C4 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP48 |
| S2V20-4000 | 1.7 A, 200 V, SILICON, RECTIFIER DIODE |
| S2V60-4070 | 1.7 A, SILICON, RECTIFIER DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29WS128J0PBFW01 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| S29WS128J0PBFW10 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| S29WS128J0PBFW11 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:128/64 Megabit (8/4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| S29WS128N | 制造商:SPANSION 制造商全称:SPANSION 功能描述:256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY |
| S29WS128N0LBAI010 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。