参数资料
| 型号： | ADV7184BSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 48/112页 |
| 文件大小： | 0K |
| 描述： | IC DECODER VID SDTV MULTI 80LQFP |
| 标准包装： | 1 |
| 类型： | 视频解码器 |
| 应用： | 投影仪，录音机，安全 |
| 电压 - 电源，模拟： | 3.15 V ~ 3.45 V |
| 电压 - 电源，数字： | 1.65 V ~ 2 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页
ADV7184
Rev. A | Page 40 of 112
7
DNR_EN, Digital Noise Reduction Enable, Address 0x4D [5]
DNR_TH2 [7:0], DNR Noise Threshold 2,
Address 0xFC [7:0]
0—Bypasses DNR (disables it).
The DNR2 block is positioned after the luma peaking block and
therefore affects the amplified luma signal. It operates in the
same way as the DNR1 block, but has an independent threshold
control, DNR_TH2 [7:0]. This value is an unsigned, 8-bit
number that determines the maximum edge that is interpreted
as noise and therefore blanked from the luma data.
Programming a large value into DNR_TH2 [7:0] causes the
DNR block to interpret even, large transients as noise and
remove them. As a result, the effect on the video data is more
visible. Programming a small value causes only small transients
to be seen as noise and to be removed.
1 (default)—Enables DNR on the luma data.
DNR_TH [7:0], DNR NoiseThreshold, Address 0x50 [7:0]
The DNR1 block is positioned before the luma peaking block.
The DNR_TH [7:0] value is an unsigned, 8-bit number that
determines the maximum edge that is interpreted as noise and
therefore blanked from the luma data. Programming a large
value into DNR_TH [7:0] causes the DNR block to interpret
even, large transients as noise and remove them. As a result, the
effect on the video data is more visible.
Programming a small value causes only small transients to be
seen as noise and to be removed.
COMB FILTERS
The comb filters of the ADV7184 have been greatly improved to
automatically handle video of all types, standards, and levels of
quality. The NTSC and PAL configuration registers allow the
user to customize comb filter operation, depending on which
video standard is detected (by autodetection) or selected (by
manual programming). In addition to the bits listed in this
section, there are other Analog Devices internal controls.
Contact an Analog Devices representative for more information.
The recommended DNR_TH [7:0] setting for A/V inputs is
0x04, and the recommended DNR_TH [7:0] setting for tuner
inputs is 0x0A.
The default value for DNR_TH [7:0] is 0x08, indicating the
threshold for maximum luma edges to be interpreted as noise.
PEAKING_GAIN [7:0], Luma Peaking Gain,
Address 0xFB [7:0]
NTSC Comb Filter Settings
This filter can be manually enabled. The user can boost or
attenuate the mid region of the Y spectrum around 3 MHz. The
peaking filter can visually improve the picture by showing more
definition on the picture details that contain frequency components
around 3 MHz. The default value (0x40) in this register passes
through the luma data unaltered (0 dB response). A lower value
attenuates the signal, and a higher value amplifies it. A plot of
the filter responses is shown in Figure 24.
Used for NTSC M and NTSC J CVBS inputs.
NSFSEL [1:0], Split Filter Selection NTSC,
Address 0x19 [3:2]
NSFSEL [1:0] selects how much of the overall signal bandwidth
is fed to the combs. A narrow bandwidth split filter results in better
performance on diagonal lines, but more dot crawl in the final
output image. The opposite is true for a wide bandwidth split filter.
15
–20
0
0
547
9-
02
4
FREQUENCY (MHz)
FILT
E
R
E
S
P
ON
S
E
(
d
B
)
10
5
0
–5
–10
–15
123456
PEAKING GAIN USING BP FILTER
Table 50. NSFSEL [1:0] Function
NSFSEL [1:0]
Description
00 (default)
Narrow
01
Medium
10
Medium
11
Wide
CTAPSN [1:0], Chroma Comb Taps NTSC,
Address 0x38 [7:6]
Table 51. CTAPSN [1:0] Function
CTAPSN [1:0]
Description
00
Do not use
01
NTSC chroma comb adapts three lines (three taps)
to two lines (two taps)
Figure 24. Peaking Filter Responses
10 (default)
NTSC chroma comb adapts five lines (five taps)
to three lines (three taps)
11
NTSC chroma comb adapts five lines (five taps)
to four lines (four taps)
相关PDF资料 |
PDF描述 |
|---|---|
| ADV7188BSTZ | IC DECODER VID MULTIFORM 80LQFP |
| ADV7189BBSTZ | IC VIDEO DECODER SDTV 80-LQFP |
| ADV7194KSTZ | IC ENCODER VIDEO EXT-10 80-LQFP |
| ADV7202KSTZ | IC CODEC VIDEO 10BIT 64LQFP |
| ADV7311KST | IC VID ENC 6-12BIT DAC'S 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADV7185 | 制造商:AD 制造商全称:Analog Devices 功能描述:Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output |
| ADV7185KST | 制造商:AD 制造商全称:Analog Devices 功能描述:Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output |
| ADV7186 | 制造商:AD 制造商全称:Analog Devices 功能描述:Video Decoder and Display Processor |
| ADV7186BBCZ | 功能描述:IC VIDEO DECODER 196CSPBGA RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064 |
| ADV7186BBCZ-RL | 功能描述:IC VIDEO DECODER 196CSPBGA RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064 |
发布紧急采购，3分钟左右您将得到回复。