- 您现在的位置：买卖IC网 > PDF目录98007 > M37902FCCHP 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M37902FCCHP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 9/143页 |
| 文件大小： | 1148K |
| 代理商： | M37902FCCHP |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页
M37902FCCHP, M37902FGCHP, M37902FJCHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
106
CPU Reprogramming Mode
The CPU reprogramming mode is used to perform the operations for
the internal flash memory (reading, programming, erasing) under
control of the CPU.
In this mode, only the user ROM area can be reprogrammed; the
boot ROM area cannot be reprogrammed.
The user-original reprogramming control software for the CPU repro-
gramming mode can be stored in either the user ROM area or the
boot ROM area. Because the CPU cannot read out the flash memory
in the CPU reprogramming mode, the above software must be trans-
ferred to the internal RAM in advance to be executed.
Boot Mode
The user-original reprogramming control software for the CPU re-
programming mode must be stored into the user ROM area or the
boot ROM area in the flash memory parallel I/O mode in advance. (If
this program has been stored into the boot ROM area, the flash
memory serial I/O mode will become unavailable).
Note that addresses of the boot ROM area depend on the accessing
ways to the boot ROM area, When accessing in the flash memory
parallel I/O mode, these addresses will be shifted to 000016 to
3FFF16 (byte address). On the other hand, when accessing with the
CPU, these addresses will be shifted to C00016 to FFFF16 (byte
address).
Reset removal with both of the MD0 and MD1 pins held “L” invokes
the normal microcomputer mode, and the CPU operates using the
control software stored in the user ROM area. In this case, the boot
ROM area is not accessible.
Removing reset with the MD0 pin held “L” and the MD1 pin “H”, the
CPU starts its operation using the reprogramming control software
stored in the boot ROM area. This mode is called the boot mode. The
reprogramming control software in the boot ROM area can also re-
program the user ROM area.
After reset removal, be sure not to change the status at pins MD0
and MD1.
Fig. 114 Bit configuration of flash memory control register
Flash memory control register
RY/BY status bit
0: Busy (Programming or erasing is active.)
1: Ready
CPU reprogramming mode select bit (Note 2)
0: Normal mode (Software commands are ignored.)
1: CPU reprogramming mode (Software commands are acceptable.)
Lock bit invalidity select bit (Note 3)
0: Block lock by lock bit data is valid.
1: Block lock by lock bit data is invalid.
Flash memory reset bit (Note 4)
0: Normal operation
1: Reset
Must be “0”.
User ROM area select bit (Note 5)
(Valid only in the boot mode.)
0: Boot ROM area access
1: User ROM area access
Address
9E16
765432
1
0
Notes 1: The contents of the flash memory control register after reset is removed are “XX0000012”.
2: To set “1”, writing of “0” to bit 1 and subsequent writing of “1” to bit 1 are necessary. Writing to bit 1
must be performed by the user-original reprogramming control software in the internal RAM.
3: To set “1”, writing of “0” to bit 2 and subsequent writing of “1” to bit 2 are necessary while bit 1 = “1”.
4: Valid only when bit 1 = “1”. Set bit 3 to “1” (reset), and then clear to “0”. This bit 3 must be controlled
with bit 1 = “1”.
5: Writing to bit 5 must be performed by the user-original reprogramming control software in the internal
RAM.
相关PDF资料 |
PDF描述 |
|---|---|
| M37902FGCHP | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37906F8CFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37902FGCGP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FGCHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FJCHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37903S4CHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905F8CFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。