- 您现在的位置：买卖IC网 > PDF目录98007 > M37902FCCHP 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M37902FCCHP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 97/143页 |
| 文件大小： | 1148K |
| 代理商： | M37902FCCHP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页当前第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页
57
M37902FCCHP, M37902FGCHP, M37902FJCHP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(3) One-shot pulse mode [10]
Figure 51 shows the bit configuration of the timer Ai mode register
during one-shot pulse mode. In one-shot pulse mode, bit 0 and bit 5
must be “0” and bit 1 and bit 2 must be “1”.
The trigger is enabled when the count start bit is “1”. The trigger can
be generated by software or it can be input from the TAiIN pin. Soft-
ware trigger is selected when bit 4 is “0” and the input signal from the
TAiIN pin is used as the trigger when it is “1“.
Bit 3 is used to determine whether to trigger at the fall of the trigger
signal or at the rise. The trigger is at the fall of the trigger signal when
bit 3 is “0” and at the rise of the trigger signal when it is “1”.
Software trigger is generated by setting “1” to a bit in the one-shot
start register. Each bit corresponds to each timer.
Figure 52 shows the bit configuration of the one-shot start register.
As shown in Figure 53, when a trigger signal is received, the counter
counts the clock selected by bits 6 and 7 and the contents of the
timer A clock division select register. (Set Table 12.)
If the contents of the counter is not 000016, the TAiOUT pin goes “H”
when a trigger signal is received. The count direction is decrement.
When the counter reaches 000116, the TAiOUT pin goes “L” and
count is stopped. The contents of the reload register is transferred to
the counter. At the same time, an interrupt request signal is gener-
ated and the interrupt request bit in the timer Ai interrupt control reg-
ister is set. This is repeated each time a trigger signal is received.
The output pulse width is
If the count start flag is “0”, TAiOUT goes “L”. Therefore, the value cor-
responding to the desired pulse width must be written to timer Ai be-
fore setting the timer Ai count start bit.
As shown in Figure 54, a trigger signal can be received before the
operation for the previous trigger signal is completed. In this case,
the contents of the reload register is transferred to the counter by the
trigger and then that value is decremented.
Except when retriggering while operating, the contents of the reload
register are not transferred to the counter by triggering.
When retriggering, there must be at least one timer count source
cycle before a new trigger can be issued.
Data write is performed in the same way as for timer mode.
When data is written in timer Ai halted, it is also written to the reload
register and the counter.
When data is written to timer Ai which is busy, the data is written to
the reload register, but not to the counter. The counter is reloaded
with new data from the reload register at the next reload time.
Undefined data is read when timer Ai is read.
1
pulse frequency of the selected clock
× (counter’s value at the time of trigger).
Fig. 51 Bit configuration of timer Ai mode register during one-shot
pulse mode
Fig. 52 Bit configuration of one-shot start register
76543210
0
1
0
1 0 : Always “10” in one-shot pulse mode
1 : Always “1” in one-shot pulse mode
0
× : Software trigger
1 0 : Trigger at the falling edge of TAiIN
input
1 1 : Trigger at the rising edge of TAiIN
input
0 : Always “0” in one-shot pulse mode
Clock source select bits
(See Table 12.)
Timer A0 mode register
Timer A1 mode register
Timer A2 mode register
Timer A3 mode register
Timer A4 mode register
Addresses
5616
5716
5816
5916
5A16
76543210
Timer A0 one-shot start bit
Timer A1 one-shot start bit
Timer A2 one-shot start bit
Timer A3 one-shot start bit
Timer A4 one-shot start bit
Must be fixed to “0”.
One-shot start register
Address
4216
0
相关PDF资料 |
PDF描述 |
|---|---|
| M37902FGCHP | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37906F8CFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37902FGCGP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FGCHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37902FJCHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37903S4CHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905F8CFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。