参数资料
型号: RC28F00BM29EWHA
厂商: Micron Technology Inc
文件页数: 26/75页
文件大小: 0K
描述: IC FLASH 2GBIT 100NS 64FBGA
标准包装: 184
系列: Axcell™
格式 - 存储器: 闪存
存储器类型: 闪存 - 或非
存储容量: 2G(256M x 8,128M x 16)
速度: 100ns
接口: 并联
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 64-LBGA
供应商设备封装: 64-FBGA(11x13)
包装: 托盘

256Mb, 512Mb, 1Gb, 2Gb: 3V Embedded Parallel NOR Flash
READ and AUTO SELECT Operations
READ and AUTO SELECT Operations
READ/RESET Command
The READ/RESET (F0h) command returns the device to read mode and resets the errors
in the status register. One or three bus WRITE operations can be used to issue the
READ/RESET command.
To return the device to read mode, this command can be issued between bus WRITE
cycles before the start of a PROGRAM or ERASE operation. If the READ/RESET com-
mand is issued during the timeout of a BLOCK ERASE operation, the device requires up
to 10 μ s to abort, during which time no valid data can be read.
This command will not abort an ERASE operation while in erase suspend.
READ CFI Command
The READ CFI (98h) command puts the device in read CFI mode and is only valid when
the device is in read array or auto select mode. One bus WRITE cycle is required to issue
the command.
Once in read CFI mode, bus READ operations will output data from the CFI memory
area (Refer to the Common Flash Interface for details). A READ/RESET command must
be issued to return the device to the previous mode (read array or auto select ). A sec-
ond READ/RESET command is required to put the device in read array mode from auto
select mode.
AUTO SELECT Command
At power-up or after a hardware reset, the device is in read mode. It can then be put in
auto select mode by issuing an AUTO SELECT (90h) command. Auto select mode ena-
bles the following device information to be read:
? Electronic signature, which includes manufacturer and device code information as
shown in the Electronic Signature table.
? Block protection, which includes the block protection status and extended memory
block protection indicator, as shown in the Block Protection table.
Electronic signature or block protection information is read by executing a READ opera-
tion with control signals and addresses set, as shown in the Read Electronic Signature
table or the Block Protection table, respectively. In addition, this device information can
be read or set by issuing an AUTO SELECT command.
Auto select mode can be used by the programming equipment to automatically match a
device with the application code to be programmed.
Three consecutive bus WRITE operations are required to issue an AUTO SELECT com-
mand. The device remains in auto select mode until a READ/RESET or READ CFI com-
mand is issued.
The device cannot enter auto select mode when a PROGRAM or ERASE operation is in
progress (RY/BY# LOW). However, auto select mode can be entered if the PROGRAM or
ERASE operation has been suspended by issuing a PROGRAM SUSPEND or ERASE SUS-
PEND command.
PDF: 09005aef849b4b09
m29ew_256mb_2gb.pdf - Rev. B 8/12 EN
26
Micron Technology, Inc. reserves the right to change products or specifications without notice.
? 2012 Micron Technology, Inc. All rights reserved.
相关PDF资料
PDF描述
RDK-242 KIT REF DESIGN VG TOPSWITCH-JX
RJCSE538001 CONN MOD JACK 8P8C SMT R/A
RJE031882420 CONN MOD JACK 8P/8C S-FLANGES
RJE051660310 CONN MOD JACK 6P/6C UNSHIELDED
RJE051880110 CONN MOD JACK 8/8 R/A UNSHIELDED
相关代理商/技术参数
参数描述
RC28F128J3A_13 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash?? Memory
RC28F128J3A-110 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-115 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-120 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-125 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)