参数资料
型号: RC28F00BM29EWHA
厂商: Micron Technology Inc
文件页数: 40/75页
文件大小: 0K
描述: IC FLASH 2GBIT 100NS 64FBGA
标准包装: 184
系列: Axcell™
格式 - 存储器: 闪存
存储器类型: 闪存 - 或非
存储容量: 2G(256M x 8,128M x 16)
速度: 100ns
接口: 并联
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 64-LBGA
供应商设备封装: 64-FBGA(11x13)
包装: 托盘

256Mb, 512Mb, 1Gb, 2Gb: 3V Embedded Parallel NOR Flash
Protection Operations
Protection Operations
Blocks can be protected individually against accidental PROGRAM, ERASE, or READ op-
erations on both 8-bit and 16-bit configurations. The block protection scheme is shown
in the Software Protection Scheme figure.
Memory block and extended memory block protection is configured through the lock
register (see Lock Register section).
LOCK REGISTER Commands
After the ENTER LOCK REGISTER COMMAND SET (40h) command has been issued, all
bus READ or PROGRAM operations can be issued to the lock register.
The PROGRAM LOCK REGISTER (A0h) command allows the lock register to be config-
ured. The programmed data can then be checked with a READ LOCK REGISTER com-
mand by driving CE# and OE# LOW with the appropriate address data on the address
bus.
PASSWORD PROTECTION Commands
After the ENTER PASSWORD PROTECTION COMMAND SET (60h) command has been
issued, the commands related to password protection mode can be issued to the device.
The PROGRAM PASSWORD (A0h) command is used to program the 64-bit password
used in the password protection mode. To program the 64-bit password, the complete
command sequence must be entered eight times at eight consecutive addresses selec-
ted by A[1:0] plus DQ15/A-1 in 8-bit mode, or four times at four consecutive addresses
selected by A[1:0] in 16-bit mode. By default, all password bits are set to 1. The password
can be checked by issuing a READ PASSWORD command.
Note: To use the password protection feature on the 2Gb device, the password must be
programmed to both upper die and lower die.
The READ PASSWORD command is used to verify the password used in password pro-
tection mode. To verify the 64-bit password, the complete command sequence must be
entered eight times at eight consecutive addresses selected by A[1:0] plus DQ15/A-1 in
8-bit mode, or four times at four consecutive addresses selected by A[1:0] in 16-bit
mode. If the password mode lock bit is programmed and the user attempts to read the
password, the device will output FFh onto the I/O data bus.
The UNLOCK PASSWORD (25/03h) command is used to clear the nonvolatile protec-
tion bit lock bit, allowing the nonvolatile protection bits to be modified. The UNLOCK
PASSWORD command must be issued, along with the correct password, and requires a
1 μ s delay between successive UNLOCK PASSWORD commands in order to prevent
hackers from cracking the password by trying all possible 64-bit combinations. If this
delay does not occur, the latest command will be ignored. Approximately 1 μ s is required
for unlocking the device after the valid 64-bit password has been provided.
NONVOLATILE PROTECTION Commands
After the ENTER NONVOLATILE PROTECTION COMMAND SET (C0h) command has
been issued, the commands related to nonvolatile protection mode can be issued to the
device.
PDF: 09005aef849b4b09
m29ew_256mb_2gb.pdf - Rev. B 8/12 EN
40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
? 2012 Micron Technology, Inc. All rights reserved.
相关PDF资料
PDF描述
RDK-242 KIT REF DESIGN VG TOPSWITCH-JX
RJCSE538001 CONN MOD JACK 8P8C SMT R/A
RJE031882420 CONN MOD JACK 8P/8C S-FLANGES
RJE051660310 CONN MOD JACK 6P/6C UNSHIELDED
RJE051880110 CONN MOD JACK 8/8 R/A UNSHIELDED
相关代理商/技术参数
参数描述
RC28F128J3A_13 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash?? Memory
RC28F128J3A-110 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-115 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-120 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)
RC28F128J3A-125 制造商:INTEL 制造商全称:Intel Corporation 功能描述:Intel StrataFlash Memory (J3)