- 您现在的位置：买卖IC网 > PDF目录1987 > AD9549ABCPZ-REEL7 (Analog Devices Inc)IC CLOCK GEN/SYNCHRONIZR 64LFCSP PDF资料下载
参数资料
| 型号： | AD9549ABCPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/76页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN/SYNCHRONIZR 64LFCSP |
| 产品变化通告： | AD9549A Mask Change 22/Oct/2010 |
| 标准包装： | 750 |
| 类型： | 时钟/频率发生器，同步器 |
| PLL： | 是 |
| 主要目的： | 以太网，SONET/SDH，Stratum |
| 输入： | CMOS，LVDS，LVPECL |
| 输出： | CMOS，HSTL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:2 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 750MHz |
| 电源电压： | 1.71 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 带卷 (TR) |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
AD9549
Rev. D | Page 11 of 76
Pin No.
Input/
Output
Pin Type
Mnemonic
Description
20, 21
O
PFD_VRB,
PFD_VRT
These pins must be capacitively decoupled. See the Phase Detector Pin
Connections section for details.
22
O
Current set
resistor
PFD_RSET
Connect a 5 k resistor from this pin to ground (see the Phase Detector Pin
Connections section).
27
I
Differential
input
SYSCLK
System Clock Input. The system clock input has internal dc biasing and should
always be ac-coupled, except when using a crystal. Single-ended 1.8 V CMOS
can also be used, but it may introduce a spur caused by an input duty cycle
that is not 50%. When using a crystal, tie the CLKMODESEL pin to AVSS, and
connect crystal directly to this pin and Pin 28.
28
I
Differential
input
SYSCLKB
Complementary System Clock. Complementary signal to the input provided
on Pin 27. Use a 0.01 μF capacitor to ground on this pin if the signal provided
on Pin 27 is single-ended.
31
O
LOOP_FILTER
System Clock Multiplier Loop Filter. When using the frequency multiplier to
drive the system clock, an external loop filter must be constructed and attached to
this pin. This pin should be pulled down to ground with a 1 k resistor when
the system clock PLL is bypassed. See Figure 44 for a diagram of the system
clock PLL loop filter.
32
I
1.8 V CMOS
CLKMODESEL
Clock Mode Select. Set to GND when connecting a crystal to the system clock
input (Pin 27 and Pin 28). Pull up to 1.8 V when using either an oscillator or an
external clock source. This pin can be left floating when the system clock PLL is
bypassed. (See the SYSCLK Inputs section for details on the use of this pin.)
33, 39, 43, 52
O
GND
AVSS
Analog Ground. Connect to ground.
34
O
1.8 V HSTL
OUTB
Complementary HSTL Output. See the Specifications and Primary 1.8 V
Differential HSTL Driver sections for details.
35
O
1.8 V HSTL
OUT
HSTL Output. See the Specifications and Primary 1.8 V Differential HSTL Driver
sections for details.
37
I
Power
AVDD3
Analog Supply for CMOS Output Driver. This pin is normally 3.3 V but can be
1.8 V. This pin should be powered even if the CMOS driver is not used. See the
Power Supply Partitioning section for power supply partitioning.
38
O
3.3 V CMOS
OUT_CMOS
CMOS Output. See the Specifications and the Output Clock Drivers and 2×
Frequency Multiplier sections. This pin is 1.8 V CMOS if Pin 37 is set to 1.8 V.
40
I
Differential
input
FDBK_INB
Complementary Feedback Input. In standard operating mode, this pin is
connected to the filtered DAC_OUTB output. This internally biased input is
typically ac-coupled, and when configured as such, can accept any differential
signal whose single-ended swing is at least 400 mV.
41
I
Differential
input
FDBK_IN
Feedback Input. In standard operating mode, this pin is connected to the
filtered DAC_OUT output.
48
O
Current set
resistor
DAC_RSET
DAC Output Current Setting Resistor. Connect a resistor (usually 10 k) from
this pin to GND. See the DAC Output section.
50
O
Differential
output
DAC_OUT
DAC Output. This signal should be filtered and sent back on chip through
FDBK_IN input. This pin has an internal 50 pull-down resistor.
51
O
Differential
output
DAC_OUTB
Complementary DAC Output. This signal should be filtered and sent back on
chip through FDBK_INB input. This pin has an internal 50 pull-down resistor.
56
I/O
3.3 V CMOS
REFSELECT
Reference Select Input. In manual mode, the REFSELECT pin operates as a high
impedance input pin; and in automatic mode, it operates as a low impedance
output pin. Logic 0 (low) indicates/selects REFA. Logic 1 (high) indicates/selects
REFB. There is no internal pull-up/pull-down resistor on this pin.
57
I/O
3.3 V CMOS
HOLDOVER
Holdover (Active High). In manual holdover mode, this pin is used to force the
AD9549 into holdover mode. In automatic holdover mode, it indicates
holdover status. There is no internal pull-up/pull-down resistor on this pin.
58
I
3.3 V CMOS
PWRDOWN
Power-Down. When this active high pin is asserted, the device becomes
inactive and enters the full power-down state. This pin has an internal 50 k
pull-down resistor.
59
I
3.3 V CMOS
RESET
Chip Reset. When this active high pin is asserted, the chip goes into reset. Note
that on power-up, it is recommended that the user assert a high to low edge
after the power supplies reach a threshold and stabilize. This pin has an
internal 50 k pull-down resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9550BCPZ-REEL7 | IC INTEGER-N TRANSLATOR 32-LFCSP |
| AD9551BCPZ | IC CLOCK GEN MULTISERV 40-LFCSP |
| AD9552BCPZ-REEL7 | IC PLL CLOCK GEN LP 32LFCSP |
| AD9553BCPZ-REEL7 | IC INTEGER-N CLCK GEN 32LFCSP |
| AD9557BCPZ-REEL7 | IC CLK XLATR PLL 1250MHZ 40LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9549APCBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Input Network Clock Generator/Synchronizer |
| AD9549BCPZ | 制造商:Analog Devices 功能描述: |
| AD9549BCPZ-REEL7 | 制造商:Analog Devices 功能描述:PLL CLOCK SYNTHESIZER SGL 64LFCSP EP - Tape and Reel |
| AD9549BCPZ-TR | 制造商:Analog Devices 功能描述:650MHZ DDS CLK GEN W/SYNCH REEL - Tape and Reel |
| AD9549XCPZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Input Network Clock Generator/Synchronizer |
发布紧急采购，3分钟左右您将得到回复。